OpenVZ Forum


Home » General » Support » venet0 and ipv6 (fully specified issue)
venet0 and ipv6 (fully specified issue) [message #51426] Thu, 29 May 2014 07:33 Go to previous message
TonyFeestneus is currently offline  TonyFeestneus
Messages: 2
Registered: May 2014
Junior Member
So, I'm new in running a VPS and am now running the following combination:

- openVZ
- 4core,3072mbram, SSD
- Ubuntu 12.04.3 32-bit
- Linux kerenl 2.6.32-042stab084.17 on i686
- Virtualmin 4.08.gpl GPL

ifconfig (ips changed for security reasons i guess):
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:40 errors:0 dropped:0 overruns:0 frame:0
TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3870 (3.8 KB) TX bytes:3870 (3.8 KB)

venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:127.0.0.2 P-t-P:127.0.0.2 Bcast:0.0.0.0 Mask:255.255.255.255
inet6 addr: 2a10:d888:3:3::513f:7c57/128 Scope:Global
inet6 addr: 2a10:d888:3:3::8c68:d2da/128 Scope:Global
inet6 addr: 2a10:d888:3:3::2b95:d43c/128 Scope:Global
inet6 addr: 2a10:d888:3:3::8560:89b5/128 Scope:Global
inet6 addr: 2a10:d888:3:3::c365:e645/128 Scope:Global
inet6 addr: 2a10:d888:3:3::d46f:5d5b/128 Scope:Global
inet6 addr: 2a10:d888:3:3::f21:4d21/128 Scope:Global
inet6 addr: 2a10:d888:3:3::f68b:2ae4/128 Scope:Global
inet6 addr: 2a10:d888:3:3::e024:905d/128 Scope:Global
inet6 addr: 2a10:d888:3:3::1b1c:4f27/128 Scope:Global
inet6 addr: 2a10:d888:3:3::469a:ec3c/128 Scope:Global
inet6 addr: 2a10:d888:3:3::b098:18f0/128 Scope:Global
inet6 addr: 2a10:d888:3:3::dc92:2cf7/128 Scope:Global
inet6 addr: 2a10:d888:3:3::270d:2c92/128 Scope:Global
inet6 addr: 2a10:d888:3:3::a7dc:a391/128 Scope:Global
inet6 addr: 2a10:d888:3:3::142a:495b/128 Scope:Global
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
RX packets:17093 errors:0 dropped:0 overruns:0 frame:0
TX packets:11653 errors:0 dropped:1 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:17125323 (17.1 MB) TX bytes:4242038 (4.2 MB)

venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:177.56.238.21 P-t-P:177.56.238.21 Bcast:0.0.0.0 Mask:255.255.255.255
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1







So, the venet0:0 has the right ipv4 address and creating virtual servers only work if I set this:
In Virtualmin>System Settings>Virtualmin Configuration>Network settings:
Network interface for virtual addresses: venet0:0

Great, but then venet0 is ignored I guess and so are all the ipv6 addresses.

How can i combine venet0 and venet0:0 in to one, to make sure all ipv6 are working and also ipv4 is still working?

Thanks a lot!!
 
Read Message
Read Message
Read Message
Previous Topic: DNS Problem
Next Topic: VPS remains offline.
Goto Forum:
  


Current Time: Wed May 31 09:48:53 GMT 2023

Total time taken to generate the page: 0.01378 seconds