OpenVZ Forum: Support » Add an private IP address into a CT

Home » General » Support » Add an private IP address into a CT

Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend

Add an private IP address into a CT [message #52423]

Tue, 07 June 2016 12:27

ekx27
Messages: 2
Registered: June 2016

Junior Member

Hi,

I recently bought a OpenVZ Container from a hosting company and I would like to add a private IP address.

Here is the default config I had :

Quote:

#ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:127.0.0.2 P-t-P:127.0.0.2 Bcast:0.0.0.0 Mask:255.255.255.255
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
RX packets:34 errors:0 dropped:0 overruns:0 frame:0
TX packets:35 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4401 (4.2 KiB) TX bytes:5688 (5.5 KiB)

venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:xxx.xxx.xxx.xxx P-t-P:xxx.xxx.xxx.xxx Bcast:xxx.xxx.xxx.xxx Mask:255.255.255.255
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1

This works, I can ping everything :

Quote:

#ping 8.8.8.8
PING 8.8.8.8 (8.8.8. 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_req=1 ttl=50 time=5.74 ms
64 bytes from 8.8.8.8: icmp_req=2 ttl=50 time=5.78 ms

If I add into the /etc/network/interface.tail the following :

Quote:

auto venet0:1
iface venet0:1 inet static
address 172.16.70.1
netmask 255.255.255.255

ifconfig result :

Quote:

~# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:127.0.0.2 P-t-P:127.0.0.2 Bcast:0.0.0.0 Mask:255.255.255.255
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
RX packets:23 errors:0 dropped:0 overruns:0 frame:0
TX packets:24 errors:0 dropped:20 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3352 (3.2 KiB) TX bytes:5067 (4.9 KiB)

venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:xxx.xxx.xxx.xxx P-t-P:xxx.xxx.xxx.xxx Bcast:xxx.xxx.xxx.xxx Mask:255.255.255.255
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1

venet0:1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:172.16.70.1 P-t-P:172.16.70.1 Bcast:172.16.70.1 Mask:255.255.255.255
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1

Then, nothing ping into the Internet...

Here is the routing table :

Quote:

#route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default * 0.0.0.0 U 0 0 0 venet0

Am I doing something wrong?

Report message to a moderator

[Message index]

		Add an private IP address into a CT By: ekx27 on Tue, 07 June 2016 12:27
		Re: Add an private IP address into a CT By: dowdle on Tue, 12 July 2016 17:01
		Re: Add an private IP address into a CT By: ekx27 on Tue, 12 July 2016 21:19

Previous Topic:	Ubuntu 16.04 kernel versions
Next Topic:	I need to refresh ARP frequently.

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sun Oct 01 11:25:58 GMT 2023

Total time taken to generate the page: 0.02879 seconds