Home » General » Support » Intermitent freeze at "initializing hardware... storage network audio"
| Intermitent freeze at "initializing hardware... storage network audio" [message #7334] |
Wed, 11 October 2006 09:39  |
fgomes
Messages: 29
Registered: August 2006
|
Junior Member |
|
|
I have a server with Dual Opteron CPU using CentOS 4.4 with OpenVZ RHEL4 kernel (ovzkernel-smp-2.6.9-023stab016.2.x86_64.rpm).
After some initial problems to put everything working in 64 bits (it was the first 64 bit linux I install), now I manage to have several VEs running well and stable. The problem that I found lately is that the system sometimes hangs when booting the hardware node (about 50% or less of the boot times), at "initializing hardware... storage network audio". I usualy reset it and enter in interactive boot and it always boot normaly when using interactive boot.
What can I do to diagnose this hanging problem?
What exactly does it mean ""initializing hardware... storage network audio"? The system has no audio... It is a server board and transport from Tyan - Tiger K8SSA (S3870) - http://www.tyan.com/products/html/tigerk8ssa.html
Another doubt I have is if it can be related with the kernel used. I'm using RHEL 4 kernel, because is the most similar to the CentOS 4.4 (I think), am I correct, or should I change to the OpenVZ stable kernel (ovzkernel-smp-2.6.8-022stab078.21.x86_64.rpm)?
Thanks for all your help!
Fernando
|
|
|
|
|
|
|
|
| Re: Intermitent freeze at "initializing hardware... storage network audio" [message #7354 is a reply to message #7338] |
Wed, 11 October 2006 21:56  |
fgomes
Messages: 29
Registered: August 2006
|
Junior Member |
|
|
Not much success with SysRq, it only writes SysRq: when I press Alt-SysRq-P or Alt-SysRq-T, both on the console and by the serial port 
I've made more than 10 boots now, it failed twice.
The hard disks are connected to a 3ware 9550SX, there are no disks on the motherboard harddisk controllers.
The most strange things I saw in this log is that sometimes I have this (2d and 3d reason):
Uhhuh. NMI received for unknown reason 3d.
Dazed and confused, but trying to continue
Do you have a strange power saving mode enabled?
and always have this:
..MP-BIOS bug: 8254 timer not connected to IO-APIC
failed.
timer doesn't work through the IO-APIC - disabling NMI Watchdog!
works.
Here is the log when it hangs:
Bootdata ok (command line is ro root=LABEL=/ console=ttyS0,57600 console=tty debug silencelevel=8)
Linux version 2.6.9-023stab016.2-smp (root@rhel4-64) (gcc version 3.4.5 20051201 (Red Hat 3.4.5-2)) #1 SMP Fri Aug 11 00:06:19 MSD 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bfff0000 (usable)
BIOS-e820: 00000000bfff0000 - 00000000bfffe000 (ACPI data)
BIOS-e820: 00000000bfffe000 - 00000000c0000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec03000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000f72c0
ACPI: XSDT (v001 A M I OEMXSDT 0x09000620 MSFT 0x00000097) @ 0x00000000bfff0100
ACPI: FADT (v003 A M I OEMFACP 0x09000620 MSFT 0x00000097) @ 0x00000000bfff0290
ACPI: MADT (v001 A M I OEMAPIC 0x09000620 MSFT 0x00000097) @ 0x00000000bfff0390
ACPI: OEMB (v001 A M I AMI_OEM 0x09000620 MSFT 0x00000097) @ 0x00000000bfffe040
ACPI: SRAT (v001 A M I OEMSRAT 0x09000620 MSFT 0x00000097) @ 0x00000000bfff3be0
ACPI: DSDT (v001 0AAAA 0AAAA000 0x00000000 INTL 0x02002026) @ 0x0000000000000000
No mptable found.
On node 0 totalpages: 1310720
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 1306624 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ServerWorks chipset detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x508
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:5 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:5 APIC version 16
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
Setting APIC routing to flat
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-15
ACPI: IOAPIC (id[0x03] address[0xfec01000] gsi_base[16])
IOAPIC[1]: apic_id 3, version 17, address 0xfec01000, GSI 16-31
ACPI: IOAPIC (id[0x04] address[0xfec02000] gsi_base[32])
IOAPIC[2]: apic_id 4, version 17, address 0xfec02000, GSI 32-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c4000000 (gap: c0000000:3ec00000)
Checking aperture...
CPU 0: aperture @ 0 size 32 MB
No AGP bridge found
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 8000000
Virtuozzo Fair CPU scheduler
Built 1 zonelists
Kernel command line: ro root=LABEL=/ console=ttyS0,57600 console=tty debug silencelevel=8
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 2194.566 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Memory: 4027060k/5242880k available (2990k kernel code, 166412k reserved, 1409k data, 216k init)
Calibrating delay using timer specific routine.. 4393.00 BogoMIPS (lpj=2196504)
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
Page beancounter hash is 524288 entries.
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU0: AMD Opteron(tm) Processor 248 stepping 01
per-CPU timeslice cutoff: 1024.20 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/1 rip 6000 rsp 1000cd47f58
Initializing CPU#1
Calibrating delay using timer specific routine.. 4388.43 BogoMIPS (lpj=2194216)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
AMD Opteron(tm) Processor 248 stepping 01
Total of 2 processors activated (8781.44 BogoMIPS).
Using local APIC timer interrupts.
Detected 12.469 MHz APIC timer.
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
Disabling vsyscall due to use of PM timer
time.c: Using PM based timekeeping.
checking if image is initramfs... it is
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:02.1
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1.P1P2._PRT]
ACPI: PCI Interrupt Link [LN00] (IRQs 3 4 5 *7 9 11 12 14 15)
ACPI: PCI Interrupt Link [LN01] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN02] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN03] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN04] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN05] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN06] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN07] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN08] (IRQs 3 4 5 6 7 *9 11 12 14 15)
ACPI: PCI Interrupt Link [LN09] (IRQs 3 4 *5 6 7 9 11 12 14 15)
ACPI: PCI Interrupt Link [LN10] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN11] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN12] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN13] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN14] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN15] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN16] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN17] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN18] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN19] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN20] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN21] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN22] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN23] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN24] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN25] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN26] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN27] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN28] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN29] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN30] (IRQs 3 4 5 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNUS] (IRQs *10)
ACPI: PCI Interrupt Link [LNSA] (IRQs *11)
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:03.1[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:03.2[A] -> GSI 10 (level, low) -> IRQ 10
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 24 (level, low) -> IRQ 16
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI interrupt 0000:00:05.0[A] -> GSI 25 (level, low) -> IRQ 17
ACPI: PCI interrupt 0000:01:0e.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:01:0e.1[A] -> GSI 11 (level, low) -> IRQ 11
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 16 (level, low) -> IRQ 18
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ 8000000 size 65536 KB
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Se
...
|
|
|
|
|
|
Goto Forum:
Current Time: Sun Jul 21 17:29:26 GMT 2024
Total time taken to generate the page: 0.02307 seconds
|
OpenVZ Forum
Members
Search
Help
Register
Login
Home
