OpenVZ Forum: Support » Networking in OpenVZ

Home » General » Support » Networking in OpenVZ

Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend

Networking in OpenVZ [message #210]

Sun, 09 October 2005 20:57

Surferdude
Messages: 11
Registered: October 2005

Junior Member

Ah, the last piece of the Puzzle... Networking. The box that I have running OpenVZ is currently hosted at LayeredTech. Over there I get a Private VLAN with 8 IP's and three used to create the VLAN which gives me 5 usable IP's. I tried allocating one of them by doing:

Quote:

vzctl set 101 --ipadd <ip here> --save

But the after doing this the VPS is not reachable via the IP i assigned it. Any ideas on why this isnt working?

Thanks

Report message to a moderator

Re: Networking in OpenVZ [message #211 is a reply to message #210]

Sun, 09 October 2005 22:22

devnu11
Messages: 64
Registered: September 2005
Location: USA

Member

DeJaVous.. My box is at Layered. The way that I made it work was to not enter the IP's through /etc/sysconfig/network-scripts. I just add them through vzctl and all is fine. I'm not sure if this is correct but it does function correctly that way. Maybe someone from SW can comment on if there is another way, but this will get you up and running for now.

Just Because You Have One, Doesn't Mean You Have To Be One!

Report message to a moderator

Re: Networking in OpenVZ [message #212 is a reply to message #211]

Sun, 09 October 2005 22:57

Surferdude
Messages: 11
Registered: October 2005

Junior Member

The IP's arent up when I add them, but it still does not work.

Report message to a moderator

Re: Networking in OpenVZ [message #213 is a reply to message #212]

Mon, 10 October 2005 00:23

devnu11
Messages: 64
Registered: September 2005
Location: USA

Member

Try using the delete command first
vzctl set 101 --ipdel 123.123.123.123 FROM ALL VPS you have created.

As root or su -l type ifconfig to show your active IP's

If you only have one your all set.

If you have more than one IP go to /etc/sysconfig/network-scripts and rename the file ifcfg-eth0-range0 by something like "mv ifcfg-eth0-range0 OLDifcfg-eth0-range0" then "/etc/init.d/network restart"

If there was only one IP showing and the VPS still does not respond I would guess you did not bind SSHD to just the main IP of the box. Not only is this essential but its helps to secure the box. Otherwise SSHD will bind to every IP you have on the box from the default sshd_config and you won't get very far with your newly created VPS.

Good Luck!

Just Because You Have One, Doesn't Mean You Have To Be One!

Report message to a moderator

Re: Networking in OpenVZ [message #214 is a reply to message #210]

Mon, 10 October 2005 07:52

dev
Messages: 1693
Registered: September 2005
Location: Moscow

Senior Member

devnu11, I will try to explain/help with networking if you describe the situation in more details.
What is the configuration you had before OVZ?
What have you tried to do and it didn't work,
and what you do know (when it works).

http://static.openvz.org/userbars/openvz-developer.png

Report message to a moderator

Re: Networking in OpenVZ [message #216 is a reply to message #214]

Mon, 10 October 2005 13:24

devnu11
Messages: 64
Registered: September 2005
Location: USA

Member

dev

When I started to install OVZ all my IP's were homed to the box. This file covered all the IP's except the main server IP:

ifcfg-eth0-range0
## Start

IPADDR_START=72.123.123.123

IPADDR_END=72.123.123.130

CLONENUM_START=0

## END

(IP changed for security purposes)

I renamed this file OLDifcfg-eth0-range0

then /etc/init.d/network restart

At this point I could add IP's via "vzctl set" and everything functioned correctly. Prior to renaming the file the IP's added via "vzctl set" added normally to the VPS but the VPS was without network connection. I was just curious if this was the correct way to do this. Hope I was clear enough.

Just Because You Have One, Doesn't Mean You Have To Be One!

Report message to a moderator

Previous Topic:	Setting RAM
Next Topic:	'non-server' devices

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Thu Sep 24 14:05:44 GMT 2026

Total time taken to generate the page: 0.43816 seconds