OpenVZ Forum: Support » Migrating physical Trixbox 2.0/Asterisk => VE: no network

Home » General » Support » Migrating physical Trixbox 2.0/Asterisk => VE: no network

Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend

Re: Migrating physical Trixbox 2.0/Asterisk => VE: no network [message #9845 is a reply to message #9790]

Thu, 25 January 2007 15:52

mperkel
Messages: 253
Registered: December 2006

Senior Member

New details.

Migght not be VE related. On the HE I can't seem to add additional IP addresses there either. The main IP works but only the main IP.

ifconfig
eth0 Link encap:Ethernet HWaddr 00:17:31:4D:C6:59
inet addr:69.50.231.8 Bcast:69.50.231.15 Mask:255.255.255.240
inet6 addr: fe80::217:31ff:fe4d:c659/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:39133654 errors:0 dropped:0 overruns:0 frame:0
TX packets:39979143 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:127239880 (121.3 MiB) TX bytes:3929486685 (3.6 GiB)
Interrupt:16 Base address:0x2000

eth0:0 Link encap:Ethernet HWaddr 00:17:31:4D:C6:59
inet addr:69.50.231.9 Bcast:69.50.231.15 Mask:255.255.255.240
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:16 Base address:0x2000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:494627 errors:0 dropped:0 overruns:0 frame:0
TX packets:494627 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:199769732 (190.5 MiB) TX bytes:199769732 (190.5 MiB)

venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

Looks normal to me but the IP address 69.50.231.9 is dead. I'm not sure what's wrong but sure could use some help. How do you troubleshoot this?

ifcfg-eth0

DEVICE=eth0
IPADDR=69.50.231.8
NETMASK=255.255.255.240
GATEWAY=69.50.231.1
ONBOOT=yes
TYPE=Ethernet
BOOTPROTO=none
USERCTL=no
PEERDNS=yes
IPV6INIT=no

ifcfg-eth0:0

IPADDR="69.50.231.9"
GATEWAY="69.50.231.1"
NETMASK=255.255.255.240
IPV6INIT=no
ONBOOT=yes
USERCTL=no
PEERDNS=yes
TYPE=Ethernet
DEVICE=eth0:0
BOOTPROTO=none

Junk Email Filter
http://www.junkemailfilter.com

Report message to a moderator

[Message index]

		Migrating physical Trixbox 2.0/Asterisk => VE: no network By: mperkel on Mon, 22 January 2007 17:08
		Re: Migrating physical Trixbox 2.0/Asterisk => VE: no network By: dim on Tue, 23 January 2007 08:51
		Re: Migrating physical Trixbox 2.0/Asterisk => VE: no network By: mperkel on Tue, 23 January 2007 14:50
		Re: Migrating physical Trixbox 2.0/Asterisk => VE: no network By: dim on Wed, 24 January 2007 09:11
		Re: Migrating physical Trixbox 2.0/Asterisk => VE: no network By: mperkel on Wed, 24 January 2007 14:54
		Re: Migrating physical Trixbox 2.0/Asterisk => VE: no network By: dim on Wed, 24 January 2007 14:57
		Re: Migrating physical Trixbox 2.0/Asterisk => VE: no network By: mperkel on Wed, 24 January 2007 15:18
		Re: Migrating physical Trixbox 2.0/Asterisk => VE: no network By: mperkel on Thu, 25 January 2007 15:52

Previous Topic:	network card does not work properly with openvz kernel
Next Topic:	SOLVED Ubuntu 6.06 - will it work

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sun Aug 03 22:06:01 GMT 2025

Total time taken to generate the page: 0.97683 seconds