| Re: *SOLVED* OpenVZ: No driver for NIC RTL8111/8168B [solved] [message #39297 is a reply to message #25385] |
Sat, 03 April 2010 20:24   |
abdicar
Messages: 17
Registered: April 2010
|
Junior Member |
|
|
I dont know what i should do now... the system show that i'm running the driver in the rev03.
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
Subsystem: Intel Corporation Unknown device d615
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 58
Region 0: I/O ports at 1000 [size=256]
Region 2: Memory at e0004000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at e0000000 (64-bit, prefetchable) [size=16K]
Expansion ROM at e0020000 [disabled] [size=128K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+
Address: 00000000fee03000 Data: 403a
Capabilities: [70] Express Endpoint IRQ 1
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <512ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [ac] MSI-X: Enable- Mask- TabSize=4
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [cc] Vital Product Data
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 00-e0-4c-68-00-00-00-03
[root@22491 cache]# lspci -n
00:00.0 0600: 8086:a000 (rev 02)
00:02.0 0300: 8086:a001 (rev 02)
00:1c.0 0604: 8086:27d0 (rev 01)
00:1c.1 0604: 8086:27d2 (rev 01)
00:1c.2 0604: 8086:27d4 (rev 01)
00:1c.3 0604: 8086:27d6 (rev 01)
00:1d.0 0c03: 8086:27c8 (rev 01)
00:1d.1 0c03: 8086:27c9 (rev 01)
00:1d.2 0c03: 8086:27ca (rev 01)
00:1d.3 0c03: 8086:27cb (rev 01)
00:1d.7 0c03: 8086:27cc (rev 01)
00:1e.0 0604: 8086:2448 (rev e1)
00:1f.0 0601: 8086:27bc (rev 01)
00:1f.2 0101: 8086:27c0 (rev 01)
00:1f.3 0c05: 8086:27da (rev 01)
01:00.0 0200: 10ec:8168 (rev 03)
So it is updated... What I can do now?
|
|
|
|
OpenVZ Forum
Members
Search
Help
Register
Login
Home
