OpenVZ Forum


Home » General » Support » howto compile kernel with some special features ? [SOLVED]
Re: howto compile kernel with some special features ? [message #37412 is a reply to message #37292] Mon, 07 September 2009 12:40 Go to previous messageGo to previous message
dvazart is currently offline  dvazart
Messages: 37
Registered: October 2008
Location: France
Member
lspci :
00:00.0 Host bridge: Intel Corporation 82946GZ/PL/GL Memory Controller Hub (rev 02)
00:02.0 VGA compatible controller: Intel Corporation 82946GZ/GL Integrated Graphics Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5 (rev 01)
00:1c.5 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
06:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller
07:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller


With 2.6.18-19-ovz-amd64 #1 SMP Wed Sep 2 18:12:15 UTC 2009 x86_64 GNU/Linux :

menu.lst
initrd		/boot/initrd.img-2.6.18-19-ovz-amd64


lsmod :
Module                  Size  Used by
vzethdev               47776  0 
vznetdev               56976  120 
simfs                  38552  60 
vzrst                 173736  0 
ip_nat                 53648  1 vzrst
vzcpt                 149432  0 
ip_conntrack          101524  3 vzrst,ip_nat,vzcpt
nfnetlink              40648  2 ip_nat,ip_conntrack
vzdquota               79216  60 [permanent]
vzmon                  84120  64 vzethdev,vznetdev,vzrst,vzcpt
vzdev                  37256  6 vzethdev,vznetdev,vzdquota,vzmon
xt_tcpudp              36480  0 
xt_length              35200  0 
ipt_ttl                35072  0 
xt_tcpmss              35584  0 
ipt_TCPMSS             37504  0 
iptable_mangle         38144  60 
iptable_filter         38016  60 
xt_multiport           36608  0 
xt_limit               36480  0 
ipt_tos                34816  0 
ipt_REJECT             39940  0 
ip_tables              57696  2 iptable_mangle,iptable_filter
x_tables               53128  10 xt_tcpudp,xt_length,ipt_ttl,xt_tcpmss,ipt_TCPMSS,xt_multiport,xt_limit,ipt_tos,ipt_REJECT,ip_tables
ipv6                  456892  373 vzrst,vzcpt,vzmon
xfrm_nalgo             43652  1 ipv6
crypto_api             43136  1 xfrm_nalgo
loop                   49040  0 
i2c_i801               42004  0 
i2c_core               56448  1 i2c_i801
pcspkr                 36480  0 
ext3                  170384  1 
jbd                   103280  1 ext3
ata_piix               57220  0 
libata                210192  1 ata_piix
floppy                 95656  0 
scsi_mod              198424  1 libata
e1000e                146256  0 
uhci_hcd               57624  0 
ehci_hcd               65932  0 

dmesg |grep hd
Command line: root=/dev/hdc2 ro quiet
Kernel command line: root=/dev/hdc2 ro quiet
testing NMI watchdog ... OK.
hdc: OCZ SUMMIT, ATA DISK drive
hdc: max request size: 512KiB
hdc: 250069680 sectors (128035 MB), CHS=16383/255/63
hdc: cache flushes supported
 hdc: hdc1 hdc2
EXT3 FS on hdc2, internal journal
hdc: status timeout: status=0xd0 { Busy }


With 2.6.26-2-amd64 #1 SMP Fri Aug 14 07:12:04 UTC 2009 x86_64 GNU/Linux :

menu.lst
initrd		/boot/initrd.img-2.6.26-2-amd64


lsmod :
Module                  Size  Used by
ipv6                  288328  16 
loop                   19468  0 
iTCO_wdt               15696  0 
snd_pcsp               14588  0 
i2c_i801               13596  0 
snd_pcm                81672  1 snd_pcsp
snd_timer              25744  1 snd_pcm
snd                    63688  3 snd_pcsp,snd_pcm,snd_timer
soundcore              12064  1 snd
snd_page_alloc         13072  1 snd_pcm
container               8320  0 
button                 11680  0 
rng_core                8968  0 
i2c_core               27936  1 i2c_i801
intel_agp              31856  1 
evdev                  14208  0 
ext3                  124944  1 
jbd                    51240  1 ext3
mbcache                12804  1 ext3
sd_mod                 29376  3 
ata_piix               22660  2 
ata_generic            10116  0 
libata                165600  2 ata_piix,ata_generic
scsi_mod              160760  2 sd_mod,libata
dock                   14112  1 libata
floppy                 61672  0 
ide_pci_generic         9220  0 [permanent]
ide_core              128284  1 ide_pci_generic
ehci_hcd               35980  0 
uhci_hcd               25760  0 
e1000e                 99748  0 
thermal                22816  0 
processor              42304  1 thermal
fan                     9352  0 
thermal_sys            17728  3 thermal,processor,fan

dmesg |grep sd
[    0.000000] Command line: root=/dev/sda2 ro quiet
[    0.000000] Kernel command line: root=/dev/sda2 ro quiet
[    2.810799] Driver 'sd' needs updating - please use bus_type methods
[    2.810881] sd 1:0:0:0: [sda] 250069680 512-byte hardware sectors (128036 MB)
[    2.810894] sd 1:0:0:0: [sda] Write Protect is off
[    2.810896] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.810915] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.810967] sd 1:0:0:0: [sda] 250069680 512-byte hardware sectors (128036 MB)
[    2.810978] sd 1:0:0:0: [sda] Write Protect is off
[    2.810980] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.810999] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.811003]  sda: sda1 sda2
[    2.810915] sd 1:0:0:0: [sda] Attached SCSI disk
[    4.572464] Adding 1951856k swap on /dev/sda1.  Priority:-1 extents:1 across:1951856k
[    4.632346] EXT3 FS on sda2, internal journal

I hope this is useful!


----------- Daniel Vazart ------------
"Knowledge is power, Sharing is human"
------- http://www.vazart.net --------
 
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Previous Topic: PCI Passthrough
Next Topic: Kernel Panic with 028stab064.4 ?
Goto Forum:
  


Current Time: Mon Aug 12 22:55:59 GMT 2024

Total time taken to generate the page: 0.03624 seconds