OpenVZ Forum: Support » DL380 G2

Home » General » Support » DL380 G2 - CCISS

Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend

Re: DL380 G2 - CCISS [message #10388 is a reply to message #10366]

Sat, 17 February 2007 02:18

gramsa49
Messages: 17
Registered: February 2007

Junior Member

Here are the results of the reinstall. Still get the warning that the cciss module does not exist when installing the openvz kernel. I need the cciss driver to use my tape drive.

0-Install CentOS 4.4
from /var/log/messages
Feb 16 18:40:10 vz1 syslogd 1.4.1: restart.
Feb 16 18:40:10 vz1 syslog: syslogd startup succeeded
Feb 16 18:40:10 vz1 kernel: klogd 1.4.1, log source = /proc/kmsg started.
Feb 16 18:40:10 vz1 kernel: Linux version 2.6.9-42.ELsmp (buildcentos@build-i386) (gcc version 3.4.6 20060404 (Red Hat 3.4.6-3)) #1 SMP Sat Aug 12 09:39:11 CDT 2006
Feb 16 18:40:10 vz1 kernel: BIOS-provided physical RAM map:
Feb 16 18:40:10 vz1 kernel: BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
Feb 16 18:40:10 vz1 kernel: BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
Feb 16 18:40:10 vz1 kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Feb 16 18:40:10 vz1 kernel: BIOS-e820: 0000000000100000 - 000000008fffc000 (usable)
Feb 16 18:40:10 vz1 kernel: BIOS-e820: 000000008fffc000 - 0000000090000000 (ACPI data)
Feb 16 18:40:10 vz1 kernel: BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
Feb 16 18:40:10 vz1 kernel: BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
Feb 16 18:40:10 vz1 kernel: BIOS-e820: 00000000ffc00000 - 0000000100000000 (reserved)
Feb 16 18:40:10 vz1 kernel: 1407MB HIGHMEM available.
Feb 16 18:40:10 vz1 kernel: 896MB LOWMEM available.
Feb 16 18:40:10 vz1 kernel: found SMP MP-table at 000f4fd0
Feb 16 18:40:10 vz1 kernel: Using x86 segment limits to approximate NX protection
Feb 16 18:40:10 vz1 syslog: klogd startup succeeded
Feb 16 18:40:10 vz1 kernel: DMI 2.3 present.
Feb 16 18:40:10 vz1 kernel: Compaq ProLiant DL380 G2 detected: force use of acpi=ht
Feb 16 18:40:10 vz1 kernel: Using APIC driver default
Feb 16 18:40:10 vz1 kernel: ACPI: PM-Timer IO Port: 0x240
Feb 16 18:40:10 vz1 kernel: ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Feb 16 18:40:10 vz1 kernel: Processor #0 6:11 APIC version 17
Feb 16 18:40:10 vz1 kernel: ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
Feb 16 18:40:10 vz1 kernel: ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
Feb 16 18:40:10 vz1 kernel: ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
Feb 16 18:40:10 vz1 kernel: Processor #3 6:11 APIC version 17
Feb 16 18:40:10 vz1 kernel: ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
Feb 16 18:40:10 vz1 kernel: Enabling APIC mode: Flat. Using 0 I/O APICs
Feb 16 18:40:10 vz1 kernel: Using ACPI for processor (LAPIC) configuration information
Feb 16 18:40:10 vz1 kernel: Intel MultiProcessor Specification v1.4
Feb 16 18:40:10 vz1 kernel: Virtual Wire compatibility mode.
Feb 16 18:40:10 vz1 kernel: OEM ID: COMPAQ Product ID: PROLIANT APIC at: 0xFEE00000
Feb 16 18:40:10 vz1 kernel: I/O APIC #8 Version 17 at 0xFEC00000.
Feb 16 18:40:10 vz1 kernel: I/O APIC #2 Version 17 at 0xFEC01000.
Feb 16 18:40:10 vz1 kernel: Enabling APIC mode: Flat. Using 2 I/O APICs
Feb 16 18:40:10 vz1 kernel: Processors: 2
Feb 16 18:40:10 vz1 kernel: Allocating PCI resources starting at 98000000 (gap: 90000000:6ec00000)
Feb 16 18:40:10 vz1 kernel: Built 1 zonelists
Feb 16 18:40:10 vz1 kernel: Kernel command line: ro root=/dev/VolGroup00/LogVol00
Feb 16 18:40:10 vz1 kernel: Initializing CPU#0
Feb 16 18:40:10 vz1 kernel: CPU 0 irqstacks, hard=c03ee000 soft=c03ce000
Feb 16 18:40:10 vz1 kernel: PID hash table entries: 4096 (order: 12, 65536 bytes)
Feb 16 18:40:10 vz1 kernel: Detected 1397.241 MHz processor.
Feb 16 18:40:10 vz1 kernel: Using pmtmr for high-res timesource
Feb 16 18:40:10 vz1 kernel: Console: colour VGA+ 80x25
Feb 16 18:40:10 vz1 kernel: Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Feb 16 18:40:10 vz1 kernel: Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Feb 16 18:40:10 vz1 kernel: Memory: 2333144k/2359280k available (1876k kernel code, 25112k reserved, 759k data, 184k init, 1441776k highmem)
Feb 16 18:40:10 vz1 kernel: Calibrating delay using timer specific routine.. 2796.70 BogoMIPS (lpj=1398354)
Feb 16 18:40:10 vz1 kernel: Security Scaffold v1.0.0 initialized
Feb 16 18:40:10 vz1 kernel: SELinux: Initializing.
Feb 16 18:40:10 vz1 kernel: SELinux: Starting in permissive mode
Feb 16 18:40:10 vz1 kernel: There is already a security framework initialized, register_security failed.
Feb 16 18:40:10 vz1 kernel: selinux_register_security: Registering secondary module capability
Feb 16 18:40:10 vz1 kernel: Capability LSM initialized as secondary
Feb 16 18:40:10 vz1 kernel: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Feb 16 18:40:10 vz1 kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
Feb 16 18:40:10 vz1 kernel: CPU: L2 cache: 512K
Feb 16 18:40:10 vz1 kernel: Intel machine check architecture supported.
Feb 16 18:40:10 vz1 kernel: Intel machine check reporting enabled on CPU#0.
Feb 16 18:40:10 vz1 kernel: Enabling fast FPU save and restore... done.
Feb 16 18:40:10 vz1 kernel: Enabling unmasked SIMD FPU exception support... done.
Feb 16 18:40:10 vz1 kernel: Checking 'hlt' instruction... OK.
Feb 16 18:40:10 vz1 kernel: CPU0: Intel(R) Pentium(R) III CPU family 1400MHz stepping 01
Feb 16 18:40:10 vz1 kernel: per-CPU timeslice cutoff: 1462.58 usecs.
Feb 16 18:40:10 vz1 kernel: task migration cache decay timeout: 2 msecs.
Feb 16 18:40:10 vz1 kernel: Booting processor 1/0 eip 3000
Feb 16 18:40:10 vz1 kernel: CPU 1 irqstacks, hard=c03ef000 soft=c03cf000
Feb 16 18:40:10 vz1 kernel: Initializing CPU#1
Feb 16 18:40:10 vz1 kernel: Calibrating delay using timer specific routine.. 2792.55 BogoMIPS (lpj=1396277)
Feb 16 18:40:10 vz1 kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
Feb 16 18:40:10 vz1 kernel: CPU: L2 cache: 512K
Feb 16 18:40:10 vz1 kernel: Intel machine check architecture supported.
Feb 16 18:40:10 vz1 kernel: Intel machine check reporting enabled on CPU#1.
Feb 16 18:40:10 vz1 kernel: CPU1: Intel(R) Pentium(R) III CPU family 1400MHz stepping 01
Feb 16 18:40:10 vz1 kernel: Total of 2 processors activated (5589.26 BogoMIPS).
Feb 16 18:40:10 vz1 kernel: ENABLING IO-APIC IRQs
Feb 16 18:40:10 vz1 kernel: ..TIMER: vector=0x31 pin1=2 pin2=0
Feb 16 18:40:10 vz1 kernel: ..MP-BIOS bug: 8254 timer not connected to IO-APIC
Feb 16 18:40:10 vz1 kernel: ...trying to set up timer (IRQ0) through the 8259A ...
Feb 16 18:40:10 vz1 kernel: ..... (found pin 0) ...works.
Feb 16 18:40:10 vz1 kernel: checking TSC synchronization across 2 CPUs: passed.
Feb 16 18:40:10 vz1 kernel: Brought up 2 CPUs
Feb 16 18:40:10 vz1 kernel: zapping low mappings.
Feb 16 18:40:10 vz1 kernel: checking if image is initramfs... it is
Feb 16 18:40:10 vz1 kernel: Freeing initrd memory: 1097k freed
Feb 16 18:40:10 vz1 kernel: NET: Registered protocol family 16
Feb 16 18:40:10 vz1 kernel: PCI: PCI BIOS revision 2.10 entry at 0xf0094, last bus=10
Feb 16 18:40:10 vz1 kernel: PCI: Using configuration type 1
Feb 16 18:40:10 vz1 kernel: mtrr: v2.0 (20020519)
Feb 16 18:40:10 vz1 kernel: mtrr: your CPUs had inconsistent fixed MTRR settings
Feb 16 18:40:10 vz1 kernel: mtrr: probably your BIOS does not setup all CPUs.
Feb 16 18:40:10 vz1 kernel: mtrr: corrected configuration.
Feb 16 18:40:10 vz1 kernel: ACPI: Subsystem revision 20040816
Feb 16 18:40:10 vz1 kernel: ACPI: Interpreter disabled.
Feb 16 18:40:10 vz1 kernel: Linux Plug and Play Support v0.97 (c) Adam Belay
Feb 16 18:40:10 vz1 kernel: usbcore: registered new driver usbfs
Feb 16 18:40:10 vz1 kernel: usbcore: registered new driver hub
Feb 16 18:40:10 vz1 kernel: PCI: Probing PCI hardware
Feb 16 18:40:10 vz1 kernel: PCI: Probing PCI hardware (bus 00)
Feb 16 18:40:10 vz1 kernel: PCI: Discovered peer bus 07
Feb 16 18:40:10 vz1 kernel: PCI: Device 00:00 not found by BIOS
Feb 16 18:40:10 vz1 kernel: PCI: Device 00:01 not found by BIOS
Feb 16 18:40:10 vz1 kernel: PCI: Device 00:02 not found by BIOS
Feb 16 18:40:10 vz1 kernel: PCI: Device 00:03 not found by BIOS
Feb 16 18:40:10 vz1 kernel: PCI: Device 00:78 not found by BIOS
Feb 16 18:40:10 vz1 kernel: apm: BIOS not found.
Feb 16 18:40:10 vz1 kernel: audit: initializing netlink socket (disabled)
Feb 16 18:40:10 vz1 kernel: audit(1171651188.085:1): initialized
Feb 16 18:40:10 vz1 kernel: highmem bounce pool size: 64 pages
Feb 16 18:40:10 vz1 kernel: Total HugeTLB memory allocated, 0
Feb 16 18:40:10 vz1 kernel: VFS: Disk quotas dquot_6.5.1
Feb 16 18:40:10 vz1 kernel: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Feb 16 18:40:10 vz1 kernel: SELinux: Registering netfilter hooks
Feb 16 18:40:10 vz1 kernel: Initializing Cryptographic API
Feb 16 18:40:10 vz1 kernel: ksign: Installing public key data
Feb 16 18:40:10 vz1 kernel: Loading keyring
Feb 16 18:40:10 vz1 kernel: - Added public key 10EA8AC2C8019830
Feb 16 18:40:10 vz1 kernel: - User ID: CentOS (Kernel Module GPG key)
Feb 16 18:40:10 vz1 kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Feb 16 18:40:10 vz1 kernel: Real Time Clock Driver v1.12
Feb 16 18:40:10 vz1 kernel: Linux agpgart interface v0.100 (c) Dave Jones
Feb 16 18:40:10 vz1 kernel: agpgart: Maximum main memory to use for agp memory: 2170M
Feb 16 18:40:10 vz1 kernel: agpgart: unable to determine aperture size.
Feb 16 18:40:10 vz1 kernel: agpgart: agp_backend_initialize() failed.
Feb 16 18:40:10 vz1 kernel: agpgart-serverworks: probe of 0000:00:00.0 failed with error -22
Feb 16 18:40:10 vz1 kernel: agpgart: Maximum main memory to use for agp memory: 2170M
Feb 16 18:40:10 vz1 kernel: agpgart: unable to determine aperture size.
Feb 16 18:40:10 vz1 kernel: agpgart: agp_backend_initialize() failed.
Feb 16 18:40:10 vz1 kernel: agpgart-serverworks: probe of 0 ...

[ Show the rest of the message ]

Report message to a moderator

[Message index]

		DL380 G2 - CCISS By: gramsa49 on Fri, 16 February 2007 04:43
		Re: DL380 G2 - CCISS By: Vasily Tarasov on Fri, 16 February 2007 07:02
		Re: DL380 G2 - CCISS By: Vasily Tarasov on Fri, 16 February 2007 14:02
		Re: DL380 G2 - CCISS By: gramsa49 on Fri, 16 February 2007 18:04
		Re: DL380 G2 - CCISS By: gramsa49 on Fri, 16 February 2007 18:03
		Re: DL380 G2 - CCISS By: gramsa49 on Fri, 16 February 2007 23:45
		Re: DL380 G2 - CCISS By: gramsa49 on Sat, 17 February 2007 02:18
		Re: DL380 G2 - CCISS By: gramsa49 on Sat, 17 February 2007 20:54
		Re: DL380 G2 - CCISS By: Vasily Tarasov on Mon, 19 February 2007 11:32
		Re: DL380 G2 - CCISS By: gramsa49 on Mon, 19 February 2007 15:43
		Re: DL380 G2 - CCISS By: gramsa49 on Mon, 19 February 2007 15:51
		Re: DL380 G2 - CCISS By: gramsa49 on Mon, 19 February 2007 19:12
		Re: DL380 G2 - CCISS By: gramsa49 on Mon, 19 February 2007 20:07
		Re: DL380 G2 - CCISS By: gramsa49 on Mon, 19 February 2007 21:33
		Re: DL380 G2 - CCISS By: Vasily Tarasov on Tue, 20 February 2007 06:34
		Re: DL380 G2 - CCISS By: gramsa49 on Tue, 20 February 2007 14:37
		Re: DL380 G2 - CCISS By: gramsa49 on Sun, 11 November 2007 19:01

Previous Topic:	Fedora 8 Problems
Next Topic:	need 2.6.19+ kernel in debian

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sun Nov 17 13:01:16 GMT 2024

Total time taken to generate the page: 0.02927 seconds