Linux version 2.6.15-1.1831_FC4 (bhcompile@tweety.build.redhat.com) (gcc version 4.0.2 20051125 (Red Hat 4.0.2-8)) #1 Tue Feb 7 13:37:42 EST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f400 (usable) BIOS-e820: 000000000009f400 - 000000000009f800 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007fff0000 (usable) BIOS-e820: 000000007fff0000 - 000000007ffff000 (ACPI data) BIOS-e820: 000000007ffff000 - 0000000080000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 1151MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000ff780 Using x86 segment limits to approximate NX protection On node 0 totalpages: 524272 DMA zone: 4096 pages, LIFO batch:0 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 294896 pages, LIFO batch:31 DMI 2.3 present. ACPI: RSDP (v000 AMI ) @ 0x000ff910 ACPI: RSDT (v001 RCC GCSL 0x00000001 MSFT 0x01000000) @ 0x7fff0000 ACPI: FADT (v001 RCC GCSL 0x00000001 MSFT 0x01000000) @ 0x7fff0030 ACPI: MADT (v001 RCC GCSL 0x00000001 MSFT 0x01000000) @ 0x7fff00b0 ACPI: DSDT (v001 RCC GCSL 0x00000100 MSFT 0x0100000d) @ 0x00000000 ACPI: PM-Timer IO Port: 0x508 ACPI: Local APIC disabled (-2); pass 'lapic' to re-enable. LAPIC disabled (-2) Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000) Built 1 zonelists Kernel command line: ro root=LABEL=/ mapped APIC to ffffd000 (00000000) Initializing CPU#0 CPU 0 irqstacks, hard=c0413000 soft=c0412000 PID hash table entries: 4096 (order: 12, 65536 bytes) Detected 2791.481 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 2073768k/2097088k available (2148k kernel code, 21980k reserved, 774k data, 196k init, 1179584k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 5587.09 BogoMIPS (lpj=11174194) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: After all inits, caps: bfebf3ff 00000000 00000000 00000080 00004400 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled mtrr: v2.0 (20020519) CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. ACPI-0610: *** Warning: Type override - [DEB_] had invalid type (Integer) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [MLIB] had invalid type (Integer) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [IO__] had invalid type (Integer) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [DATA] had invalid type (String) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [SIO_] had invalid type (String) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [SB__] had invalid type (String) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [ICNT] had invalid type (String) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [ACPI] had invalid type (String) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [IORG] had invalid type (String) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [SB__] had invalid type (String) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [SIO_] had invalid type (String) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [BIOS] had invalid type (Integer) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [CMOS] had invalid type (Integer) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [KBC_] had invalid type (Integer) for Scope operator, changed to (Scope) ACPI-0610: *** Warning: Type override - [OEM_] had invalid type (Integer) for Scope operator, changed to (Scope) ACPI: setting ELCR to 0200 (from 0e20) Local APIC disabled by default; use 'lapic' to enable it. checking if image is initramfs... it is Freeing initrd memory: 1148k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfdba1, last bus=3 PCI: Using configuration type 1 ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [NRTH] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: _BBN and _CRS returns different value for \_SB_.PCI1. Select _CRS ACPI: _BBN and _CRS returns different value for \_SB_.PCI2. Select _CRS Boot video device is 0000:00:07.0 PCI: Ignoring BAR0-3 of IDE controller 0000:00:0f.1 ACPI: PCI Interrupt Routing Table [\_SB_.NRTH._PRT] ACPI: PCI _CRS 1 overrides _BBN 0 ACPI: PCI Root Bridge [PCI1] (0000:01) PCI: Probing PCI hardware (bus 01) ACPI: _BBN and _CRS returns different value for \_SB_.PCI1. Select _CRS ACPI: _BBN and _CRS returns different value for \_SB_.PCI2. Select _CRS ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT] ACPI: PCI _CRS 3 overrides _BBN 0 ACPI: PCI Root Bridge [PCI2] (0000:03) PCI: Probing PCI hardware (bus 03) ACPI: _BBN and _CRS returns different value for \_SB_.PCI1. Select _CRS ACPI: _BBN and _CRS returns different value for \_SB_.PCI2. Select _CRS ACPI: PCI Interrupt Routing Table [\_SB_.PCI2._PRT] ACPI: PCI Interrupt Link [LN00] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN01] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN02] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN03] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN04] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN05] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN06] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN07] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN08] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN09] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN10] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN11] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN12] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN13] (IRQs 3 4 5 7 9 11 12 14 15) *1 ACPI: PCI Interrupt Link [LN14] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN15] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN16] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN17] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN18] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN19] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN20] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN21] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN22] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN23] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN24] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN25] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN26] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN27] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN28] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN29] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN30] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LN31] (IRQs 3 4 5 7 9 11 12 14 15) *0 ACPI: PCI Interrupt Link [LNUS] (IRQs 10) *1 Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 12 devices usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:01: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:01: ioport range 0x40b-0x40b has been reserved pnp: 00:01: ioport range 0x4d6-0x4d6 has been reserved pnp: 00:01: ioport range 0xc14-0xc14 has been reserved pnp: 00:01: ioport range 0xc49-0xc49 has been reserved pnp: 00:01: ioport range 0xc52-0xc52 has been reserved pnp: 00:01: ioport range 0xc6c-0xc6c has been reserved PCI: Bridge: 0000:01:03.0 IO window: 8000-afff MEM window: fe600000-fe7fffff PREFETCH window: fb000000-fb0fffff apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) audit(1141236836.088:1): initialized highmem bounce pool size: 64 pages Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API ksign: Installing public key data Loading keyring - Added public key BBAAC818B8690C98 - User ID: Red Hat, Inc. (Kernel Module GPG key) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered PCI: MSI quirk detected. pci_msi_quirk set. PCI: MSI quirk detected. pci_msi_quirk set. pci_hotplug: PCI Hot Plug PCI Core version: 0.5 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12 Linux agpgart interface v0.101 (c) Dave Jones PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx IT8212: IDE controller at PCI slot 0000:00:05.0 ACPI: PCI Interrupt Link [LN13] BIOS reported IRQ 0, using IRQ 9 ACPI: PCI Interrupt Link [LN13] enabled at IRQ 9 PCI: setting IRQ 9 as level-triggered ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LN13] -> GSI 9 (level, low) -> IRQ 9 IT8212: chipset revision 17 it821x: controller in smart mode. IT8212: 100% native mode on irq 9 ide0: BM-DMA at 0x6000-0x6007, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x6008-0x600f, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... hda: Integrated Technology Express Inc, ATA DISK drive hda: IT8212 RAID 0 volume(64K stripe). ide0 at 0x7400-0x7407,0x7002 on irq 9 Probing IDE interface ide1... SvrWks CSB5: IDE controller at PCI slot 0000:00:0f.1 SvrWks CSB5: chipset revision 147 SvrWks CSB5: not 100% native mode: will probe irqs later ide2: BM-DMA at 0xffa0-0xffa7, BIOS settings: hde:DMA, hdf:DMA ide3: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdg:pio, hdh:pio Probing IDE interface ide2... hde: ST3200822A, ATA DISK drive hdf: SAMSUNG SC-140B, ATAPI CD/DVD-ROM drive ide2 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide3... Probing IDE interface ide1... Probing IDE interface ide3... hda: max request size: 128KiB hda: 781443840 sectors (400099 MB), CHS=48642/255/63 hda: cache flushes not supported hda: hda1 < hda5 hda6 > hde: max request size: 1024KiB hde: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100) hde: cache flushes supported hde: hde1 hde2 hde3 hde4 < hde5 hde6 hde7 hde8 hde9 > hdf: ATAPI 40X CD-ROM drive, 128kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 ide-floppy driver 0.99.newide usbcore: registered new driver libusual usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1310720 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode ACPI wakeup devices: SLPB NRTH PS2M PS2K USB PCI1 PCI2 ACPI: (supports S0 S1 S4 S5) Freeing unused kernel memory: 196k freed Write protecting the kernel read-only data: 337k input: AT Translated Set 2 keyboard as /class/input/input0 SCSI subsystem initialized 3ware Storage Controller device driver for Linux v1.26.02.001. ACPI: PCI Interrupt Link [LN02] BIOS reported IRQ 0, using IRQ 9 ACPI: PCI Interrupt Link [LN02] enabled at IRQ 9 ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LN02] -> GSI 9 (level, low) -> IRQ 9 input: ImExPS/2 Generic Explorer Mouse as /class/input/input1 scsi0 : 3ware Storage Controller 3w-xxxx: scsi0: Found a 3ware Storage Controller at 0x5400, IRQ: 9. Vendor: 3ware Model: Logical Disk 0 Rev: 1.2 Type: Direct-Access ANSI SCSI revision: 00 SCSI device sda: 1470698112 512-byte hdwr sectors (752997 MB) SCSI device sda: drive cache: write back SCSI device sda: 1470698112 512-byte hdwr sectors (752997 MB) SCSI device sda: drive cache: write back sda: sda1 sd 0:0:0:0: Attached scsi disk sda kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: Disabled at runtime. SELinux: Unregistering netfilter hooks Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 Ethernet Channel Bonding Driver: v2.6.5 (November 4, 2005) bonding: MII link monitoring set to 100 ms Intel(R) PRO/1000 Network Driver - version 6.1.16-k2-NAPI Copyright (c) 1999-2005 Intel Corporation. ACPI: PCI Interrupt Link [LN04] BIOS reported IRQ 0, using IRQ 9 ACPI: PCI Interrupt Link [LN04] enabled at IRQ 9 ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LN04] -> GSI 9 (level, low) -> IRQ 9 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection ACPI: PCI Interrupt Link [LN05] BIOS reported IRQ 0, using IRQ 9 ACPI: PCI Interrupt Link [LN05] enabled at IRQ 9 ACPI: PCI Interrupt 0000:02:04.1[B] -> Link [LN05] -> GSI 9 (level, low) -> IRQ 9 e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection ACPI: PCI Interrupt Link [LN06] BIOS reported IRQ 0, using IRQ 9 ACPI: PCI Interrupt Link [LN06] enabled at IRQ 9 ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [LN06] -> GSI 9 (level, low) -> IRQ 9 e1000: eth2: e1000_probe: Intel(R) PRO/1000 Network Connection ACPI: PCI Interrupt Link [LN07] BIOS reported IRQ 0, using IRQ 9 ACPI: PCI Interrupt Link [LN07] enabled at IRQ 9 ACPI: PCI Interrupt 0000:02:06.1[B] -> Link [LN07] -> GSI 9 (level, low) -> IRQ 9 e1000: eth3: e1000_probe: Intel(R) PRO/1000 Network Connection ACPI: PCI Interrupt Link [LN00] BIOS reported IRQ 0, using IRQ 9 ACPI: PCI Interrupt Link [LN00] enabled at IRQ 9 ACPI: PCI Interrupt 0000:03:07.0[A] -> Link [LN00] -> GSI 9 (level, low) -> IRQ 9 e1000: eth4: e1000_probe: Intel(R) PRO/1000 Network Connection e100: Intel(R) PRO/100 Network Driver, 3.4.14-k4-NAPI e100: Copyright(c) 1999-2005 Intel Corporation ACPI: PCI Interrupt Link [LN15] BIOS reported IRQ 0, using IRQ 11 ACPI: PCI Interrupt Link [LN15] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LN15] -> GSI 11 (level, low) -> IRQ 11 e100: eth5: e100_probe: addr 0xfe5ff000, irq 11, MAC addr 00:E0:81:29:24:D4 eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin and others scb2_flash: warning - can't reserve rom window, continuing CFI: Found no SCB2 BIOS Flash device at location zero scb2_flash: flash probe failed! ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [LNUS] BIOS reported IRQ 1, using IRQ 10 ACPI: PCI Interrupt Link [LNUS] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:00:0f.2[A] -> Link [LNUS] -> GSI 10 (level, low) -> IRQ 10 ohci_hcd 0000:00:0f.2: OHCI Host Controller ohci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:0f.2: irq 10, io mem 0xfd5fe000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (FF) [SLPF] ACPI: Sleep Button (CM) [SLPB] ibm_acpi: ec object not found md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com cdrom: open failed. cdrom: open failed. EXT3 FS on hde3, internal journal JFS: nTxBlock = 8192, nTxLock = 65536 kjournald starting. Commit interval 5 seconds EXT3 FS on hde9, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hde2, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hde8, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hde5, internal journal EXT3-fs: mounted filesystem with ordered data mode. Adding 4192924k swap on /dev/hde6. Priority:-1 extents:1 across:4192924k 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller e1000: eth0: e1000_watchdog_task: NIC Link is Up 1000 Mbps Full Duplex bonding: bond0: enslaving eth0 as an active interface with an up link. e1000: eth1: e1000_watchdog_task: NIC Link is Up 1000 Mbps Full Duplex bonding: bond0: enslaving eth1 as an active interface with an up link. e1000: eth2: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex bonding: bond1: enslaving eth2 as an active interface with an up link. e1000: eth4: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex bonding: bond1: enslaving eth4 as an active interface with an up link. e1000: eth3: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex bonding: bond2: enslaving eth3 as an active interface with an up link. e100: eth5: e100_watchdog: link up, 100Mbps, full-duplex bonding: bond2: enslaving eth5 as an active interface with an up link. bond0.110: add 01:00:5e:00:00:01 mcast address to master interface bond1.200: add 01:00:5e:00:00:01 mcast address to master interface bond2.300: add 01:00:5e:00:00:01 mcast address to master interface i2c /dev entries driver bond0.110: add 01:00:5e:00:00:fb mcast address to master interface bond1.200: add 01:00:5e:00:00:fb mcast address to master interface bond2.300: add 01:00:5e:00:00:fb mcast address to master interface parport: PnPBIOS parport detected. parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] lp0: using parport0 (interrupt-driven). lp0: console ready NET: Registered protocol family 10 lo: Disabled Privacy Extensions bond0.110: add 33:33:00:00:00:01 mcast address to master interface bond0.110: add 33:33:ff:09:a6:44 mcast address to master interface bond1.200: add 33:33:00:00:00:01 mcast address to master interface bond1.200: add 33:33:ff:09:a6:46 mcast address to master interface bond2.300: add 33:33:00:00:00:01 mcast address to master interface bond2.300: add 33:33:ff:09:a6:47 mcast address to master interface IPv6 over IPv4 tunneling driver ip_tables: (C) 2000-2002 Netfilter core team eth0: no IPv6 routers present bond2.300: no IPv6 routers present eth2: no IPv6 routers present bond1.200: no IPv6 routers present bond0.110: no IPv6 routers present eth1: no IPv6 routers present bond1: no IPv6 routers present eth5: no IPv6 routers present eth4: no IPv6 routers present eth3: no IPv6 routers present bond2: no IPv6 routers present bond0: no IPv6 routers present