Initializing cgroup subsys cpuset
Linux version 2.6.24-openvz-24-004.1d1-686 (2.6.24-6) (ola@tigereye) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Wed Apr 30 00:32:01 CEST 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 0000000000098000 (usable)
 BIOS-e820: 0000000000098000 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
 BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001ff70000 (usable)
 BIOS-e820: 000000001ff70000 - 000000001ff7a000 (ACPI data)
 BIOS-e820: 000000001ff7a000 - 000000001ff80000 (ACPI NVS)
 BIOS-e820: 000000001ff80000 - 0000000020000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
 BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
found SMP MP-table at 000f6680
Entering add_active_range(0, 0, 130928) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   130928
  HighMem    130928 ->   130928
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   130928
On node 0 totalpages: 130928
  DMA zone: 36 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4060 pages, LIFO batch:0
  Normal zone: 1114 pages used for memmap
  Normal zone: 125718 pages, LIFO batch:31
  HighMem zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
DMI present.
ACPI: RSDP 000F66B0, 0014 (r0 PTLTD )
ACPI: RSDT 1FF75B79, 0038 (r1 PTLTD    RSDT    6040000  LTP        0)
ACPI: FACP 1FF79E69, 0074 (r1 INTEL  CANTWOOD  6040000 PTL         3)
ACPI: DSDT 1FF75BB1, 42B8 (r1  INTEL CANTWOOD  6040000 MSFT  100000B)
ACPI: FACS 1FF7AFC0, 0040
ACPI: SPCR 1FF79EDD, 0050 (r1 PTLTD  $UCRTBL$  6040000 PTL         1)
ACPI: APIC 1FF79F2D, 0074 (r1 PTLTD  	 APIC    6040000  LTP        0)
ACPI: BOOT 1FF79FA1, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
ACPI: SSDT 1FF79FC9, 0037 (r1 PTLTD  ACPIHT    6040000  LTP        1)
ACPI: DMI detected: Fujitsu Siemens
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:3 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:3 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfec10000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 32, address 0xfec10000, GSI 24-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 2 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
swsusp: Registered nosave memory region: 0000000000098000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d2000
swsusp: Registered nosave memory region: 00000000000d2000 - 00000000000d4000
swsusp: Registered nosave memory region: 00000000000d4000 - 00000000000dc000
swsusp: Registered nosave memory region: 00000000000dc000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 129778
Kernel command line: root=/dev/sda2 ro quiet
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
mapped IOAPIC to ffff9000 (fec10000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 3000.723 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 509148k/523712k available (1788k kernel code, 13996k reserved, 696k data, 248k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff4c000 - 0xfffff000   ( 716 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xe0800000 - 0xff7fe000   ( 495 MB)
    lowmem  : 0xc0000000 - 0xdff70000   ( 511 MB)
      .init : 0xc0374000 - 0xc03b2000   ( 248 kB)
      .data : 0xc02bf395 - 0xc036d484   ( 696 kB)
      .text : 0xc0100000 - 0xc02bf395   (1788 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 6006.02 BogoMIPS (lpj=12012056)
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b180 0000441d 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Page beancounter hash is 32768 entries.
CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6001.52 BogoMIPS (lpj=12003043)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b180 0000441d 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04
Total of 2 processors activated (12007.54 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
net_namespace: 76 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd920, last bus=4
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CSA_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 10 11 14 15) *5
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 10 11 14 15) *7
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 10 *11 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 9 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
system 00:01: ioport range 0x1000-0x107f has been reserved
system 00:01: ioport range 0x1180-0x11bf has been reserved
system 00:01: ioport range 0x12e-0x12f has been reserved
system 00:01: ioport range 0x372-0x375 has been reserved
system 00:01: ioport range 0x377-0x377 has been reserved
system 00:01: ioport range 0x4d0-0x4d1 has been reserved
system 00:01: ioport range 0x600-0x67f has been reserved
system 00:01: ioport range 0xca2-0xca5 has been reserved
system 00:01: ioport range 0xfe00-0xfe00 has been reserved
system 00:01: ioport range 0xfe10-0xfe11 has been reserved
system 00:01: iomem range 0xfecf0000-0xfecfffff could not be reserved
system 00:01: iomem range 0xfed20000-0xfed8ffff has been reserved
PCI: Bridge: 0000:00:03.0
  IO window: 2000-2fff
  MEM window: f8100000-f81fffff
  PREFETCH window: 30000000-300fffff
PCI: Bridge: 0000:00:1c.0
  IO window: 3000-3fff
  MEM window: f8200000-f82fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: 4000-4fff
  MEM window: f8300000-f9ffffff
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs... it is
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
Freeing initrd memory: 5833k freed
Simple Boot Flag at 0x38 set to 0x1
audit: initializing netlink socket (disabled)
audit(1231349476.892:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:04:05.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 248k freed
ACPI: CPU0 (power states: C1[C1] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: CPU1 (power states: C1[C1] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 17, io base 0x00001420
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:02:01.0 to 64
e1000: 0000:02:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:0a:e4:13:16:62
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
libata version 3.00 loaded.
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI Interrupt 0000:04:06.0[A] -> GSI 17 (level, low) -> IRQ 19
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xf8000400
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
e1000: 0000:04:06.0: e1000_probe: (PCI:33MHz:32-bit) 00:0a:e4:13:16:63
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
sata_promise 0000:03:04.0: version 2.11
ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 26 (level, low) -> IRQ 21
scsi0 : sata_promise
scsi1 : sata_promise
scsi2 : sata_promise
scsi3 : sata_promise
ata1: SATA max UDMA/133 mmio m4096@0xf8220000 port 0xf8220200 irq 21
ata2: SATA max UDMA/133 mmio m4096@0xf8220000 port 0xf8220280 irq 21
ata3: SATA max UDMA/133 mmio m4096@0xf8220000 port 0xf8220300 irq 21
ata4: SATA max UDMA/133 mmio m4096@0xf8220000 port 0xf8220380 irq 21
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-6: ST3160023AS, 3.05, max UDMA/133
ata1.00: 312581808 sectors, multi 0: LBA48 
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 0)
ata3: SATA link down (SStatus 0 SControl 0)
ata4: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      ST3160023AS      3.05 PQ: 0 ANSI: 5
ICH5: IDE controller (0x8086:0x25a2 rev 0x02) at  PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH5: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1460-0x1467, BIOS settings: hda:pio, hdb:pio
ICH5: IDE port disabled
Probing IDE interface ide0...
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
hda: HL-DT-STDVD-ROM GDR8082N, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 24X DVD-ROM drive, 256kB Cache
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
udevd version 125 started
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
intel_rng: FWH not detected
EDAC MC: Ver: 2.1.0 Apr 30 2008
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
iTCO_wdt: Found a 6300ESB TCO device (Version=1, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
EDAC i82875p: i82875p init one
EDAC MC0: Giving out device to 'i82875p_edac' 'i82875p': DEV 0000:00:00.0
EDAC PCI0: Giving out device to module 'i82875p_edac' controller 'EDAC PCI controller': DEV '0000:00:00.0' (POLLED)
Linux agpgart interface v0.102
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 19
input: PC Speaker as /class/input/input2
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k
Adding 1951856k swap on /dev/sda1.  Priority:-1 extents:1 across:1951856k
EXT3 FS on sda2, internal journal
loop: module loaded
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
NET: Registered protocol family 10
Bridge firewalling registered
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device eth0 entered promiscuous mode
audit(1231349493.830:2): dev=eth0 prom=256 old_prom=0 auid=4294967295
br0: port 1(eth0) entering learning state
ip_tables: (C) 2000-2006 Netfilter Core Team
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
eth0: no IPv6 routers present
br0: no IPv6 routers present
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
CT: 101: started
device veth101.0 entered promiscuous mode
audit(1231392638.318:3): dev=veth101.0 prom=256 old_prom=0 auid=4294967295
br0: port 2(veth101.0) entering learning state
veth101.0: no IPv6 routers present
eth0: no IPv6 routers present
br0: topology change detected, propagating
br0: port 2(veth101.0) entering forwarding state
NFS locking service started (ver 0.5).
