OpenVZ Forum: Support » *SOLVED* openvz and trixbox

Home » General » Support » *SOLVED* openvz and trixbox

Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend

*SOLVED* openvz and trixbox [message #9004]

Wed, 13 December 2006 07:33

sanjooz_2002
Messages: 19
Registered: October 2006

Junior Member

Hi,

I have successfully installed OpenVZ and have created 4 virtual servers on it. I have trixbox running in each one of them. I have subscribed for a VoIP number and connect the incoming call on that number to the dialplan. The registration of the VoIP number is successful. I could see the message 'registered' after typing "iax2 show registry" on the asterisk console. The problem is, when the above config is used in any one of my vps es (ofcourse after the unregistration of the VoIP number from other machines) the inbound call gets rejected by the vps. What is puzzling is this that, the same coniguration works perfectly fine on other systems .i.e the non OpenVZ ones.Im unsure if the prob is with OpenVZ or with trixbox.
And yes, by the way all the systems at my end run CentOS .i.e both virtual and the main hardware node. Can anyone help?Thanks in advance!

[Updated on: Fri, 22 December 2006 09:05] by Moderator

Report message to a moderator

Re: openvz and trixbox [message #9024 is a reply to message #9004]

Wed, 13 December 2006 15:47

rickb
Messages: 368
Registered: October 2006

Senior Member

Hi,

First, copy your asterisk software to the HN, fire it up and try to receive the call. This will isolate whether the problem is a problem due to the environment being virtualized.

Are you reliant on the ztdummy/zaptel kernel modules? If so, you will need to grant each VE access:

for x in `ls /dev/zap`; do /usr/sbin/vzctl set VEID --devnodes zap/${x}:rw --save; done

Hope this helps or points you in the right direction.

Rick

-------------
Common Terms I post with: http://wiki.openvz.org/Category:Definitions

UBC. Learn it, love it, live it: http://wiki.openvz.org/Proc/user_beancounters

Report message to a moderator

Re: openvz and trixbox [message #9198 is a reply to message #9024]

Thu, 21 December 2006 21:50

johan_hammy
Messages: 99
Registered: December 2005

Member

Do you run that on the HN or the VE?

Will that also allow access to ztdummy, or only real zaptel?

Also, is zaptel to be compiled on the HN?

[Updated on: Thu, 21 December 2006 21:52]

Report message to a moderator

Re: openvz and trixbox [message #9217 is a reply to message #9004]

Fri, 22 December 2006 07:20

sanjooz_2002
Messages: 19
Registered: October 2006

Junior Member

Hi,

Firstly, I request the moderator to put the *solved* status on the title for this thread, since I have fixed this problem. Actually the problem occured due to some technical fault at the VoIP service provider' end. Moreover, I modified my standard iax.conf file to the format in which the VoIP service provider (Voicepulse)had suggested on their website.

As far as Johan' que goes, the answer is no. My virtual servers have no access to Zaptel. I really doubt if that is possible. As I am not an expert, kindly confirm the same from a professional.

Thanks!!!

OPENVZ ROCKS!!!!!!!!!!!!!

cheers'

Report message to a moderator

Re: openvz and trixbox [message #9218 is a reply to message #9004]

Fri, 22 December 2006 07:22

sanjooz_2002
Messages: 19
Registered: October 2006

Junior Member

I forgot to add that, trixbox runs on each of virtual servers and not the HN and I am not using the Zaptel functionality anywhere in my system.

Thanks!
cheers'

[Updated on: Fri, 22 December 2006 07:26]

Report message to a moderator