OpenVZ Forum: Devel » 64bit DMA in i2o

Home » Mailing lists » Devel » 64bit DMA in i2o_block

Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend

Re: 64bit DMA in i2o_block [message #6775 is a reply to message #6768]

Fri, 22 September 2006 10:14

Markus Lidel
Messages: 7
Registered: March 2006

Junior Member

Hello,

Vasily Averin wrote:
> I've found that your driver does not work correctly with following options:
> CONFIG_I2O_EXT_ADAPTEC=y
> # CONFIG_I2O_EXT_ADAPTEC_DMA64 is not set
> I've checked it on 2.6.18 kernel on x86_64 node with 4Gb memory.

That could be the reason for the problems. I've only tried it on x86_64
machines with < 4 GB memory...

> I would note that I've not noticed any bugs on x86 kernels, but x86_64 does not
> work at all.
> The behaviors of x86_64 kernels can differ:
> sometimes driver can not find partition table:
> i2o/hda: unknown partition table
> sometimes it find not all partition:
> i2o/hda: i2o/hda1 i2o/hda2 i2o/hda3 i2o/hda4 < >
> in other cases it detects devices well but corrupt the memory and filesystem:
> Sep 21 16:46:09 ts10 block-osm: registered device at major 80
> Sep 21 16:46:09 ts10 i2o/hda: i2o/hda1 i2o/hda2 i2o/hda3 i2o/hda4 < i2o/hda5 >
> Sep 21 16:46:09 ts10 block-osm: device added (TID: 207): i2o/hda
> Sep 21 16:46:09 ts10 kjournald starting. Commit interval 5 seconds
> Sep 21 16:46:09 ts10 EXT3-fs: mounted filesystem with ordered data mode.
> Sep 21 16:46:10 ts10 Freeing unused kernel memory: 236k freed
> Sep 21 16:46:10 ts10 hotplug[961]: segfault at 0000000000000008 rip
> 00000032411088cf rsp 00007fff5b189050 error 4
> When I enabled CONFIG_I2O_EXT_ADAPTEC_DMA64 -- all the troubles went away.
> I've tried to investigate this issue, but I've not found and documentation
> described format of Adaptec's private messages.
> I would like to ask you, is this behavior specific for my hardware (Adaptec
> ASR-2010S I2O Zero Channel)? If not, I believe it makes sense to enable
> CONFIG_I2O_EXT_ADAPTEC_DMA64 in Kconfig by default for 64-bit kernels.

I believe it's a driver issue. Do you have a testing-system where you
could try out the appended patch?

Thank you very much.

Best regards,

Markus Lidel
------------------------------------------
Markus Lidel (Senior IT Consultant)

Shadow Connect GmbH
Carl-Reisch-Weg 12
D-86381 Krumbach
Germany

Phone: +49 82 82/99 51-0
Fax: +49 82 82/99 51-11

E-Mail: Markus.Lidel@shadowconnect.com
URL: http://www.shadowconnect.com

Report message to a moderator

[Message index]

		64bit DMA in i2o_block By: vaverin on Fri, 22 September 2006 09:10
		Re: 64bit DMA in i2o_block By: Markus Lidel on Fri, 22 September 2006 10:14
		Re: 64bit DMA in i2o_block By: Andi Kleen on Fri, 22 September 2006 10:54
		Re: 64bit DMA in i2o_block By: Markus Lidel on Fri, 22 September 2006 11:47
		Re: 64bit DMA in i2o_block By: vaverin on Fri, 22 September 2006 11:39
		Re: 64bit DMA in i2o_block By: vaverin on Wed, 04 October 2006 09:42

Previous Topic:	[RFC] network namespaces
Next Topic:	dpt_i2o: cycle with interrupts disabled

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Tue Feb 17 07:51:20 GMT 2026

Total time taken to generate the page: 0.15846 seconds