OpenVZ Forum: Support » [Help]

Home » General » Support » [Help] - Ip change (How to change IP from class 10.0.0. to 10.0.1.)

Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend

[Help] - Ip change [message #40694]

Tue, 21 September 2010 14:04

g_dallan@yahoo.com
Messages: 3
Registered: September 2010

Junior Member

Dear Reader,
first of all thank you for you attention and time.

THE PROBLEM(this is just an example - I have some virtual servers):

The main server IP is 1.0.0.40 (not "natted")

The virtual server IP is 10.0.0.38 ("natted", for example 111.111.111.112)

All is working well: the virtual server send and receive (i.e. apache + postfix).

Now I have to change all the IP (the main server and all the virtual servers) from 10.0.0.xxx to 10.0.1.xxx

WHAT I HAVE DONE

I tried to delete the old virtual IP (10.0.0.38) and reassign a new IP (10.0.1.38).

If I try to connect by browser to my website (http://10.0.1.38), I get the (html) page.

But there's an error: (for example) if this page try to send and email (to my yahoo account), inside the page code by php mail, command, the mailq shows the following error:

(delivery temporarily suspended: Host or domain name not found. Name service error for name=yahoo.com type=MX: Host not found, try again)

I think it depends on gateway, but I do not know how to solve the problem.

The route -n command shows:

Destination Gateway Genmask Flags Metric Ref Use Iface
10.0.1.38 0.0.0.0 255.255.255.255 UH 0 0 0 venet0
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0
10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth0
0.0.0.0 10.0.0.200 0.0.0.0 UG 0 0 0 eth0

Can you help me?

PS. excuse me for my bad english. I'm a linux newbie. Thank you again.

Report message to a moderator

Re: [Help] - Ip change [message #40695 is a reply to message #40694]

Tue, 21 September 2010 14:34

TheStig
Messages: 94
Registered: December 2008

Member

did you or you nameservice provider change the mx and the reverse entry of your mailserver to the new ip address?

Report message to a moderator

Re: [Help] - Ip change [message #40696 is a reply to message #40695]

Tue, 21 September 2010 15:36

g_dallan@yahoo.com
Messages: 3
Registered: September 2010

Junior Member

Quote:

did you or you nameservice provider change the mx and the reverse entry of your mailserver to the new ip address?

I think the problem is in the gateway configuration.

The problem is not in the MX (or mailserver). In the same page I do a curl call. With 10.0.0.38 it works right. With 10.0.1.38 it does not.

$ch=curl_init();
	$url="http://www.google.it";
	curl_setopt($ch, CURLOPT_URL,$url);
	curl_setopt($ch, CURLOPT_PORT , 80);
	curl_setopt($ch, CURLOPT_RETURNTRANSFER,1);
$result=curl_exec($ch);
curl_close($ch);
//
echo($result);

Report message to a moderator

Re: [Help] - Ip change [message #40721 is a reply to message #40696]

Thu, 23 September 2010 13:10

maratrus
Messages: 1495
Registered: August 2007
Location: Moscow

Senior Member

Hello,

lets try to localize the problem i.e.
are you able to:
- reach any host from inside the VE (except the HN)
- reach your VE from outside (except the HN)
?

I suppose VE<---->HN works just fine,
but you are not able to reach either the VE from outside or outside from the VE or both cases happen.

Different subnets might be the reason. Why do you expect your VE to be reachable? It belongs to different subnet than HN.

Try to set "NEIGHBOUR_DEVS=all" in /etc/vz/vz.conf and restart vz service. But make sure that it is technically possible to have a VE belonging to different subnet.

Report message to a moderator

Re: [Help] - Ip change [message #40722 is a reply to message #40721]

Thu, 23 September 2010 13:48

g_dallan@yahoo.com
Messages: 3
Registered: September 2010

Junior Member

Thank you maratrus,
I will try in the next days.

Thank you again,
gil

Report message to a moderator

Previous Topic:	Kernel Names
Next Topic:	running cobbler inside a CT

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Tue Jul 21 16:06:34 GMT 2026

Total time taken to generate the page: 0.13703 seconds