looking for opinions for host server hardware setup [message #37469] |
Tue, 15 September 2009 01:33 ![Go to next message Go to next message](/theme/ovz3/images/down.png) |
zogthegreat
Messages: 1 Registered: May 2009 Location: Montreal, Canada
|
Junior Member |
|
|
Hi everyone,
I am looking for opinions for host server hardware setup. Here are my system hardware specs:
motherboard: Tyan S2735 w/ 2x's P4 2.6
memory: 6 gig DDR 2100 ECC
HDD: 2 x 40 gig Seagate SATA hard drives
HDD: 4 x 500 gig Seagate IDE hard drives on a 3Ware 7500 RAID controller in a RAID 5 configuration
NIC's: (on-board)
eth0: Intel 82551QM 10/100
eth1: Intel 82546EB Gigabit
eth2: Intel 82546EB Gigabit
OS: CentOS 5.3 (PAE kernel to address greater than 3 gig of ram)
Planned use:
Host OS will be CentOS 5.3 installed on the 2 x 40 gig SATA's a RAID 1, (mirror), configuration. I have an on-board hardware raid controller on the motherboard, (yes, it is a real hardware RAID, not "fakeraid"). Eth0 will be assigned to it with an ip address of 192.168.x.x.
I want to have several guest machines on this. I intend to create a virtual Samba server and mount my 4 x's 500 gig array from my existing Samba server under that. I would like to assign eth1 to this machine with an ip address of 192.168.x.x.
I then want to create guest machines for web, email and ftp servers with a virtual reverse proxy server to mange the whole thing, (web side, not Samba). I would then like to assign eth2 to this "side" with an address range of 10.0.x.x.
Everything will be connected to a Smoothwall Express firewall configured in the following manner:
eth0, (red) ADSL modem
eth1, (green), local area network with ip range of 192.168.x.x
eth2, (orange), DMZ with ip range of 10.0.x.x
So, here are my questions:
1: Should I use the default installer formatting or would I be better off manually creating the partitions?
I was considering the following:
/boot 100 meg
/swap 8 gig (6 gig hardware memory, plus two gig extra)
/ 5 gig
/etc 2 gig
/opt 1 gig
/var 1 gig
/usr 5 gig
/usr/local 2 gig
/tmp 2 gig
/home 19 gig (approx)
2: Is the manner that I want to setup my NIC:s workable, (i.e. the different ip ranges). Can anyone point me in the direction of websites where I can get a better understanding of how to configure the guest machines NIC's, (yes, I am reading the wiki).
Any suggestions or pointers would be appreciated.
Thanks
zog
|
|
|
|
Re: looking for opinions for host server hardware setup [message #37547 is a reply to message #37469] |
Fri, 25 September 2009 03:42 ![Go to previous message Go to previous message](/theme/ovz3/images/up.png) |
mperkel
Messages: 253 Registered: December 2006
|
Senior Member |
|
|
I'd do a different hardware configuration. I tend to like Opterons over Intel for servers and I'd get a MB that holds more ram. What you're buying is an odd configuration. You can get quad core CPUs with 8G ram on a $75 MB.
Rather than 4 500G drives in Raid 5 (slow) and an expensive controller I would get 4 1T drives and do Raid 10 which is just as fast using what you call fake raid and faster than Raid 5.
Since 1T drives are under $100 you can save the price of the high dollar controller and run faster and have more storage using Raid 10. I don't think you need Raid 1 for a boot drive. I would just make a small boot partition on the raid 1 array. It would partition each drive as follows:
100m boot
4G swap
4G /
rest of the drive /vz
Junk Email Filter
http://www.junkemailfilter.com
|
|
|