OpenVZ Forum


Home » General » Support » openvz hangs on boot on fujitsu-siemens blade rack unit (solved!)
openvz hangs on boot on fujitsu-siemens blade rack unit (solved!) [message #29464] Mon, 14 April 2008 10:37 Go to next message
eerov is currently offline  eerov
Messages: 8
Registered: April 2008
Junior Member
openvz hangs on boot on fujitsu-siemens blade rack unit.
After keyboard and mouse is detected, system just hangs / waits for ever.

Any solution to this. System is running 64bit version of centos 5.1 with latest stable openvz-kernel. Blade is with 12GB of memory and fiber switch.

greetings,
eerov@welho.com

--
Eero

[Updated on: Sun, 20 April 2008 13:45]

Report message to a moderator

Re: openvz hangs on boot on fujitsu-siemens blade rack unit [message #29476 is a reply to message #29464] Mon, 14 April 2008 22:07 Go to previous messageGo to next message
OpenAdmin is currently offline  OpenAdmin
Messages: 7
Registered: April 2008
Junior Member
This sounds like a hardware issue and not an openvz issue since it never starts to boot, right? It doesn't even reach the boot loader?

Report message to a moderator

Re: openvz hangs on boot on fujitsu-siemens blade rack unit [message #29478 is a reply to message #29476] Mon, 14 April 2008 22:19 Go to previous messageGo to next message
eerov is currently offline  eerov
Messages: 8
Registered: April 2008
Junior Member
Bootloader loads and boots.

After kernel starts mouse and keyboard detection, after
that it just waits / hangs. Hard to say.

It works fine on pure centos 5.1 kernel, so I think this is openvz kernel issue.

Report message to a moderator

Re: openvz hangs on boot on fujitsu-siemens blade rack unit [message #29479 is a reply to message #29478] Mon, 14 April 2008 23:00 Go to previous messageGo to next message
OpenAdmin is currently offline  OpenAdmin
Messages: 7
Registered: April 2008
Junior Member
Did it ever worked or you just installed it and it never worked? Which kernel are you on?

Report message to a moderator

Re: openvz hangs on boot on fujitsu-siemens blade rack unit [message #29480 is a reply to message #29479] Mon, 14 April 2008 23:05 Go to previous messageGo to next message
eerov is currently offline  eerov
Messages: 8
Registered: April 2008
Junior Member
Well.

As I said, it is running latest (stable) openvz enterprise kernel for centos 5.1 (rhel).

Report message to a moderator

Re: openvz hangs on boot on fujitsu-siemens blade rack unit [message #29486 is a reply to message #29480] Tue, 15 April 2008 09:30 Go to previous messageGo to next message
drescherjm is currently offline  drescherjm
Messages: 27
Registered: February 2008
Junior Member
Did it work for any other (non openvz) kernel? How about a 2.6.18 kernel?

[Updated on: Tue, 15 April 2008 09:31]

Report message to a moderator

Re: openvz hangs on boot on fujitsu-siemens blade rack unit [message #29487 is a reply to message #29486] Tue, 15 April 2008 09:39 Go to previous messageGo to next message
eerov is currently offline  eerov
Messages: 8
Registered: April 2008
Junior Member
It works on basic and updated Centos 5.1 kernel, so this looks to me like openvz kernel bug issue.

Currently looking way to track this down, or some boot parameter that allows me to boot openvz kernel.

Report message to a moderator

Re: openvz hangs on boot on fujitsu-siemens blade rack unit [message #29508 is a reply to message #29487] Tue, 15 April 2008 13:26 Go to previous messageGo to next message
drescherjm is currently offline  drescherjm
Messages: 27
Registered: February 2008
Junior Member
Do you know if the basic Centos 5.1 kernel is 2.6.18? I ask this because the stable openvz kernel is 2.6.18 and that is quite old. It is patched to fix bugs since 2.6.18 was introduced but it may not support your hardware if your hardware is very new. Also it could be a configuration settings difference between the two kernels.

Report message to a moderator

Re: openvz hangs on boot on fujitsu-siemens blade rack unit [message #29515 is a reply to message #29464] Tue, 15 April 2008 16:20 Go to previous messageGo to next message
maratrus is currently offline  maratrus
Messages: 1495
Registered: August 2007
Location: Moscow
Senior Member
Hello,

1. Could you please tell us the exact version of OpenVZ kernel you use? Where have you got it?

2. Could you please show us the messages you've got during the boot time?

Report message to a moderator

Re: openvz hangs on boot on fujitsu-siemens blade rack unit [message #29518 is a reply to message #29515] Tue, 15 April 2008 16:59 Go to previous messageGo to next message
eerov is currently offline  eerov
Messages: 8
Registered: April 2008
Junior Member
kernel is ovzkernel-ent-2.6.18-53.1.13.el5.028stab053.10
from official repo using yum.

I need to capture messages using digital camera or pen

Report message to a moderator

Re: openvz hangs on boot on fujitsu-siemens blade rack unit [message #29519 is a reply to message #29518] Tue, 15 April 2008 17:06 Go to previous messageGo to next message
drescherjm is currently offline  drescherjm
Messages: 27
Registered: February 2008
Junior Member
If you have access to a null modem cable you can easily set up a serial console to grab the boot messages.


http://wiki.sangoma.com/wanpipe-linux-system-debugging

Report message to a moderator

Re: openvz hangs on boot on fujitsu-siemens blade rack unit [message #29520 is a reply to message #29519] Tue, 15 April 2008 17:09 Go to previous messageGo to next message
eerov is currently offline  eerov
Messages: 8
Registered: April 2008
Junior Member
No, I can't since blade units don't have any serialports.

Any other way to debug this kernel?

It works on other machine, so I think that issue is hardware related. It works on standard kernel, so I think this is openvz related issue.

Report message to a moderator

Re: openvz hangs on boot on fujitsu-siemens blade rack unit [message #29536 is a reply to message #29520] Wed, 16 April 2008 08:15 Go to previous messageGo to next message
maratrus is currently offline  maratrus
Messages: 1495
Registered: August 2007
Location: Moscow
Senior Member
Hello,

64bit OS and i386 kernel (vzkernel-ent-2.6.18-53.1.13.el5.028stab053.10.i686).

could you possibly try x86_64 kernel, please?

Report message to a moderator

Re: openvz hangs on boot on fujitsu-siemens blade rack unit (solved) [message #29646 is a reply to message #29536] Sun, 20 April 2008 13:44 Go to previous message
eerov is currently offline  eerov
Messages: 8
Registered: April 2008
Junior Member
Thanks, it worked.

Anyway, looks like packaging bug since installin vzkernel-ent install wrong architechture (i686) kernel instead of amd64.

Report message to a moderator

Previous Topic: Fedora 5 and 6
Next Topic: Duplicating working VPS with tar/cp
Goto Forum:
  

[ Syndicate this forum (XML) ] [ RSS ] [ PDF ]

Current Time: Wed Feb 18 08:45:16 GMT 2026

Total time taken to generate the page: 0.59097 seconds
Powered by FUDforum Powered by Virtuozzo Containers