OpenVZ Forum: Support » eth0 dies when using openVZ kernel.

Home » General » Support » eth0 dies when using openVZ kernel.

Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend

Re: eth0 dies when using openVZ kernel. [message #27918 is a reply to message #27096]

Mon, 03 March 2008 08:43

thorpe
Messages: 16
Registered: February 2008
Location: Sydney - Australia

Junior Member

This still isn't working. eth0 just drops off the face of the earcth after about a minute. yet if a look at ifconfig it all looks normal.

route comes up blank after eth0 dies.

Ive got no idea where to start looking, here is a cat of /var/log/messages from the time I boot into the vz kernal till the time I need to reboot back into my normal working kernel.

Anyone got any ideas? Or can recommend some vitualization that I might be able to get working?

[code]
Mar 3 19:16:46 oblivion kernel: Linux version 2.6.18-ovz-028stab051.1 () (tsd@debian.systs.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Fri Dec 7 19:42:24 CET 2007
Mar 3 19:16:46 oblivion kernel: BIOS-provided physical RAM map:
Mar 3 19:16:46 oblivion kernel: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
Mar 3 19:16:46 oblivion kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Mar 3 19:16:46 oblivion kernel: BIOS-e820: 0000000000100000 - 000000001ff77000 (usable)
Mar 3 19:16:46 oblivion kernel: BIOS-e820: 000000001ff77000 - 000000001ff79000 (ACPI NVS)
Mar 3 19:16:46 oblivion kernel: BIOS-e820: 000000001ff79000 - 0000000020000000 (reserved)
Mar 3 19:16:46 oblivion kernel: BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
Mar 3 19:16:46 oblivion kernel: BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
Mar 3 19:16:46 oblivion kernel: BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
Mar 3 19:16:46 oblivion kernel: 0MB HIGHMEM available.
Mar 3 19:16:46 oblivion kernel: 511MB LOWMEM available.
Mar 3 19:16:46 oblivion kernel: found SMP MP-table at 000fe710
Mar 3 19:16:46 oblivion kernel: DMI 2.3 present.
Mar 3 19:16:46 oblivion kernel: ACPI: PM-Timer IO Port: 0x808
Mar 3 19:16:46 oblivion kernel: ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Mar 3 19:16:46 oblivion kernel: Processor #0 15:2 APIC version 20
Mar 3 19:16:46 oblivion kernel: ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
Mar 3 19:16:46 oblivion kernel: ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
Mar 3 19:16:46 oblivion kernel: IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
Mar 3 19:16:46 oblivion kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Mar 3 19:16:46 oblivion kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Mar 3 19:16:46 oblivion kernel: Enabling APIC mode: Flat. Using 1 I/O APICs
Mar 3 19:16:46 oblivion kernel: Using ACPI (MADT) for SMP configuration information
Mar 3 19:16:46 oblivion kernel: Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Mar 3 19:16:46 oblivion kernel: Detected 2254.151 MHz processor.
Mar 3 19:16:46 oblivion kernel: Built 1 zonelists. Total pages: 130935
Mar 3 19:16:46 oblivion kernel: Kernel command line: root=/dev/hda9 ro
Mar 3 19:16:46 oblivion kernel: Enabling fast FPU save and restore... done.
Mar 3 19:16:46 oblivion kernel: Enabling unmasked SIMD FPU exception support... done.
Mar 3 19:16:46 oblivion kernel: Initializing CPU#0
Mar 3 19:16:46 oblivion kernel: CPU 0 irqstacks, hard=c05bf000 soft=c05be000
Mar 3 19:16:46 oblivion kernel: PID hash table entries: 2048 (order: 11, 8192 bytes)
Mar 3 19:16:46 oblivion kernel: Console: colour VGA+ 80x25
Mar 3 19:16:46 oblivion kernel: Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Mar 3 19:16:46 oblivion kernel: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mar 3 19:16:46 oblivion kernel: Memory: 510144k/523740k available (3475k kernel code, 13056k reserved, 1083k data, 272k init, 0k highmem)
Mar 3 19:16:46 oblivion kernel: Checking if this processor honours the WP bit even in supervisor mode... Ok.
Mar 3 19:16:46 oblivion kernel: Calibrating delay using timer specific routine.. 4509.75 BogoMIPS (lpj=2254879)
Mar 3 19:16:46 oblivion kernel: Mount-cache hash table entries: 512
Mar 3 19:16:46 oblivion kernel: CPU: Trace cache: 12K uops, L1 D cache: 8K
Mar 3 19:16:46 oblivion kernel: CPU: L2 cache: 512K
Mar 3 19:16:46 oblivion kernel: Intel machine check architecture supported.
Mar 3 19:16:46 oblivion kernel: Intel machine check reporting enabled on CPU#0.
Mar 3 19:16:46 oblivion kernel: CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
Mar 3 19:16:46 oblivion kernel: CPU0: Thermal monitoring enabled
Mar 3 19:16:46 oblivion kernel: Compat vDSO mapped to ffffe000.
Mar 3 19:16:46 oblivion kernel: CPU: Intel(R) Pentium(R) 4 CPU 2.26GHz stepping 04
Mar 3 19:16:46 oblivion kernel: Checking 'hlt' instruction... OK.
Mar 3 19:16:46 oblivion kernel: ACPI: Core revision 20060707
Mar 3 19:16:46 oblivion kernel: Page beancounter hash is 32768 entries.
Mar 3 19:16:46 oblivion kernel: ENABLING IO-APIC IRQs
Mar 3 19:16:46 oblivion kernel: ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Mar 3 19:16:46 oblivion kernel: checking if image is initramfs... it is
Mar 3 19:16:46 oblivion kernel: Freeing initrd memory: 2715k freed
Mar 3 19:16:46 oblivion kernel: NET: Registered protocol family 16
Mar 3 19:16:46 oblivion kernel: ACPI: bus type pci registered
Mar 3 19:16:46 oblivion kernel: PCI: PCI BIOS revision 2.10 entry at 0xfbeae, last bus=2
Mar 3 19:16:46 oblivion kernel: PCI: Using configuration type 1
Mar 3 19:16:46 oblivion kernel: Setting up standard PCI resources
Mar 3 19:16:46 oblivion kernel: ACPI: Interpreter enabled
Mar 3 19:16:46 oblivion kernel: ACPI: Using IOAPIC for interrupt routing
Mar 3 19:16:46 oblivion kernel: ACPI: PCI Root Bridge [PCI0] (0000:00)
Mar 3 19:16:46 oblivion kernel: ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Mar 3 19:16:46 oblivion kernel: PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
Mar 3 19:16:46 oblivion kernel: PCI quirk: region 0880-08bf claimed by ICH4 GPIO
Mar 3 19:16:46 oblivion kernel: PCI: Transparent bridge - 0000:00:1e.0
Mar 3 19:16:46 oblivion kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 6 7 9 10 11 12 15)
Mar 3 19:16:46 oblivion kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
Mar 3 19:16:46 oblivion kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 15)
Mar 3 19:16:46 oblivion kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 15)
Mar 3 19:16:46 oblivion kernel: ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
Mar 3 19:16:46 oblivion kernel: ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
Mar 3 19:16:46 oblivion kernel: ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
Mar 3 19:16:46 oblivion kernel: ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 15)
Mar 3 19:16:46 oblivion kernel: SCSI subsystem initialized
Mar 3 19:16:46 oblivion kernel: PCI: Using ACPI for IRQ routing
Mar 3 19:16:46 oblivion kernel: PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Mar 3 19:16:46 oblivion kernel: PCI: Bridge: 0000:00:01.0
Mar 3 19:16:46 oblivion kernel: IO window: disabled.
Mar 3 19:16:46 oblivion kernel: MEM window: fb000000-fdffffff
Mar 3 19:16:46 oblivion kernel: PREFETCH window: e0000000-efffffff
Mar 3 19:16:46 oblivion kernel: PCI: Bridge: 0000:00:1e.0
Mar 3 19:16:46 oblivion kernel: IO window: e000-efff
Mar 3 19:16:46 oblivion kernel: MEM window: fe100000-fe2fffff
Mar 3 19:16:46 oblivion kernel: PREFETCH window: 30000000-300fffff
Mar 3 19:16:46 oblivion kernel: NET: Registered protocol family 2
Mar 3 19:16:46 oblivion kernel: IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Mar 3 19:16:46 oblivion kernel: TCP established hash table entries: 16384 (order: 4, 65536 bytes)
Mar 3 19:16:46 oblivion kernel: TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
Mar 3 19:16:46 oblivion kernel: TCP: Hash tables configured (established 16384 bind 8192)
Mar 3 19:16:46 oblivion kernel: TCP reno registered
Mar 3 19:16:46 oblivion kernel: Simple Boot Flag at 0x7a set to 0x80
Mar 3 19:16:46 oblivion kernel: VFS: Disk quotas dquot_6.5.1
Mar 3 19:16:46 oblivion kernel: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Mar 3 19:16:46 oblivion kernel: Initializing Cryptographic API
Mar 3 19:16:46 oblivion kernel: io scheduler noop registered
Mar 3 19:16:46 oblivion kernel: io scheduler anticipatory registered
Mar 3 19:16:46 oblivion kernel: io scheduler deadline registered
Mar 3 19:16:46 oblivion kernel: io scheduler cfq registered (default)
Mar 3 19:16:46 oblivion kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Mar 3 19:16:46 oblivion kernel: Real Time Clock Driver v1.12ac
Mar 3 19:16:46 oblivion kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
Mar 3 19:16:46 oblivion kernel: serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Mar 3 19:16:46 oblivion kernel: RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Mar 3 19:16:46 oblivion kernel: Compaq SMART2 Driver (v 2.6.0)
Mar 3 19:16:46 oblivion kernel: HP CISS Driver (v 3.6.10)
Mar 3 19:16:46 oblivion kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Mar 3 19:16:46 oblivion kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Mar 3 19:16:46 oblivion kernel: ICH2: IDE controller at PCI slot 0000:00:1f.1
Mar 3 19:16:46 oblivion kernel: ICH2: chipset revision 4
Mar 3 19:16:46 oblivion kernel: ICH2: not 100%% native mode: will probe irqs later
Mar 3 19:16:46 oblivion kernel: ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
Mar 3 19:16:46 oblivion kernel: ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Mar 3 19:16:46 oblivion kernel: hda: WDC WD800BB-75CAA0, ATA DISK drive
Mar 3 19:16:46 oblivion kernel: hdb: ST3320620A, ATA DISK drive
Mar 3 19:16:46 oblivion kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Mar 3 19:16:46 obl ...

[ Show the rest of the message ]

Report message to a moderator

[Message index]

		eth0 dies when using openVZ kernel. By: thorpe on Sat, 09 February 2008 06:32
		Re: eth0 dies when using openVZ kernel. By: maratrus on Sat, 09 February 2008 20:12
		Re: eth0 dies when using openVZ kernel. By: den on Mon, 03 March 2008 12:00
		Re: eth0 dies when using openVZ kernel. By: thorpe on Tue, 04 March 2008 05:23
		Re: eth0 dies when using openVZ kernel. By: thorpe on Mon, 03 March 2008 08:43
		Re: eth0 dies when using openVZ kernel. By: den on Tue, 04 March 2008 06:13
		Re: eth0 dies when using openVZ kernel. By: thorpe on Tue, 04 March 2008 07:24
		Re: eth0 dies when using openVZ kernel. By: den on Tue, 04 March 2008 08:04
		Re: eth0 dies when using openVZ kernel. By: thorpe on Tue, 04 March 2008 08:52
		Re: eth0 dies when using openVZ kernel. By: thorpe on Tue, 04 March 2008 09:30
		Re: eth0 dies when using openVZ kernel. By: den on Tue, 04 March 2008 11:22
		SOLVED By: thorpe on Wed, 05 March 2008 04:07

Previous Topic:	Quota Problem
Next Topic:	Internet access from VE (again)

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sat Aug 17 09:11:30 GMT 2024

Total time taken to generate the page: 0.02901 seconds