OpenVZ Forum: Support » trying to install image magick via yum i get error Error: hal conflicts with kernel

Home » General » Support » trying to install image magick via yum i get error Error: hal conflicts with kernel < 2.6.17

Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend

trying to install image magick via yum i get error Error: hal conflicts with kernel < 2.6.17 [message #27549]

Tue, 19 February 2008 11:43

slonghurst
Messages: 40
Registered: September 2006
Location: UK

Member

when i check on the virtual node what kernal is used,

uname -r
2.6.18-8.1.15.el5.028stab049.1

it brings back the kernel of the host node which is greater than 2.6.17

Any help greatly appreciated

Report message to a moderator

Re: trying to install image magick via yum i get error Error: hal conflicts with kernel < 2.6.17 [message #27584 is a reply to message #27549]

Wed, 20 February 2008 06:33

maratrus
Messages: 1495
Registered: August 2007
Location: Moscow

Senior Member

Hi,

I suppose that it is some dummy package inside VPS which provides kernel capability. Try to

rpm -q --whatprovides kernel

inside VPS. And try to remove that package.

Report message to a moderator

Re: trying to install image magick via yum i get error Error: hal conflicts with kernel < 2.6.17 [message #27794 is a reply to message #27584]

Wed, 27 February 2008 14:16

slonghurst
Messages: 40
Registered: September 2006
Location: UK

Member

hi

sorry for the delay, have only just got back to being able to look at this. When execute that command i get this

# rpm -q --whatprovides kernel
dummy-fedora-core-4-1.0-4.swsoft

i then try

rpm -e dummy-fedora-core-4-1.0-4.swsoft

to which i get these errors.

error: Failed dependencies:
ethtool >= 1.8-2 is needed by (installed) initscripts-8.54.1-1.i386
mingetty is needed by (installed) initscripts-8.54.1-1.i386
module-init-tools is needed by (installed) initscripts-8.54.1-1.i386

I installed the fedora template from the community created section so i guesss it is a problem with this. On the plus side i downloaded the source imagemagick and forced the install and we can now use the functions we wanted. Would be nice to know how to get round this in future though

Report message to a moderator

Re: trying to install image magick via yum i get error Error: hal conflicts with kernel < 2.6.17 [message #27848 is a reply to message #27549]

Fri, 29 February 2008 08:49

xemul
Messages: 248
Registered: November 2005

Senior Member

Try to tune your VE's uname -r with /proc/sys/kernel/virt_osrelease file. Maybe the installer just checks this one.

http://static.openvz.org/userbars/openvz-developer.png

Report message to a moderator

Re: trying to install image magick via yum i get error Error: hal conflicts with kernel < 2.6.17 [message #27856 is a reply to message #27794]

Fri, 29 February 2008 12:27

maratrus
Messages: 1495
Registered: August 2007
Location: Moscow

Senior Member

Hi,

Before give you any piece of advice I'll try to explain my point of view.
The issue is in the following:
We have a dummy package which provides some kinds of capabilities. To observe them please use rpm command:

rpm -q --provides PACK_NAME

(in your case PACK_NAME=dummy-fedora-core-4-1.0-4.swsoft). As you can see this package is a fake package (it might provide capability but mightn't contain the corresponding utility). I only know two reasons why it was made:
a) Some packages need the capability for example

Quote:

 module-init-tools is needed by (installed) initscripts-8.54.1-1.i386

but actually we cannot load modules from inside VE. And we have to provide this or may be some else capability.
b) We don't want to increase VE's weight so we don't add some unnecessary utilities.

In your case you could look at

rpm -q --provides PACK_NAME

output and install inside VE appropriate packages, for example in your case, kernel,module-init-tools, ethtool, mingetty etc (the common Fedora-4 packages) and then remove dummy package from inside the VE.

I suppose that everything should work and you'll be able to install appropriate software.

Report message to a moderator

Re: trying to install image magick via yum i get error Error: hal conflicts with kernel < 2.6.17 [message #38679 is a reply to message #27856]

Fri, 15 January 2010 03:18

dedicados
Messages: 46
Registered: February 2009
Location: Mexico

Member

when i try to upgrade my centos, i get error like that

Convert: bla bla bla is needed by package samba

i do

#yum remove samba

and now i can upgrade my OS

Report message to a moderator

Previous Topic:	A Big problem with my vps
Next Topic:	PAE support inside VE

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sat Nov 29 13:01:15 GMT 2025

Total time taken to generate the page: 0.25894 seconds