OpenVZ Forum: Support » using network aliases

Home » General » Support » using network aliases

Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend

using network aliases [message #2011]

Tue, 14 March 2006 12:05

bhazeltn
Messages: 5
Registered: March 2006

Junior Member

I'm trying to assign eth0:2 to a vps, but I can't seem to figure it out

mainserv bradley # ifconfig eth0:2
eth0:2    Link encap:Ethernet  HWaddr xx:xx:xx:xx:xx:xx  
          inet addr:xxx.xxx.xxx.xxx  Bcast:xxx.xxx.xxx.xxx Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          Interrupt:11 Base address:0xc000

mainserv bradley # vzctl set 101 --netdev_add eth0:2
Unable to add netdev eth0:2: No such process

Is there a way to do this?

Report message to a moderator

Re: using network aliases [message #2012 is a reply to message #2011]

Tue, 14 March 2006 13:31

kir
Messages: 1645
Registered: August 2005
Location: Moscow, Russia

Senior Member

No, you can only give a real network device to a VPS.

BTW why do you need this?

Kir Kolyshkin

http://static.openvz.org/userbars/openvz-developer.png

Report message to a moderator

Re: using network aliases [message #2013 is a reply to message #2012]

Tue, 14 March 2006 15:51

bhazeltn
Messages: 5
Registered: March 2006

Junior Member

It is a dedicated server that I don't have physical access too that has one network card buy multiple IP's, some that I wish to map directly to the vps

Report message to a moderator

Re: using network aliases [message #2014 is a reply to message #2013]

Tue, 14 March 2006 15:57

kir
Messages: 1645
Registered: August 2005
Location: Moscow, Russia

Senior Member

Well that's pretty straightforward.

What you need to do is
(1) remove those extra IPs from eth0 interface (leaving just the one address for the server itself);
(2) add those IPs to the appropriate VPSs, i.e.

vzctl set NNN --ipadd a.b.c.d --save

Kir Kolyshkin

Report message to a moderator

Re: using network aliases [message #2015 is a reply to message #2013]

Tue, 14 March 2006 16:07

bhazeltn
Messages: 5
Registered: March 2006

Junior Member

that's simple enough. I had alredy assinged the IP to the VPS, but, this was helpful. thanks

Report message to a moderator

Re: using network aliases [message #2016 is a reply to message #2014]

Tue, 14 March 2006 16:44

bhazeltn
Messages: 5
Registered: March 2006

Junior Member

Ok, now I'm stumped again.
I removed eth0:2 from my network config. The IP was already assigned to the vps. The vps starts fine. I go to ping the IP and I get no response.

I do have /etc/sysctl.conf set up according to the quick install directions (however they are not in the gentoo howto)

I'm using Gentoo, which I figure probably makes this crap out on me

Report message to a moderator

Re: using network aliases [message #2017 is a reply to message #2016]

Tue, 14 March 2006 17:53

bhazeltn
Messages: 5
Registered: March 2006

Junior Member

I sorted it out, it took some playing, but I got it to work.

The primary and secondary address I have use a different default gateway, I just had to make the vps know this

Report message to a moderator

Previous Topic:	Question about memory resource parameters
Next Topic:	iptables in vps or on the host node

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Mon Jul 27 23:17:57 GMT 2026

Total time taken to generate the page: 3.01087 seconds