OpenVZ Forum: Users » IPv6 with venet

Home » Mailing lists » Users » IPv6 with venet

Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend

Re: IPv6 with venet [message #14769 is a reply to message #14752]

Tue, 10 July 2007 07:40

Jan Tomasek
Messages: 44
Registered: December 2006

Member

Vitaliy Gusev wrote:
> Please check /proc/sys/net/ipv6/conf/all/forwarding

It is disabled:

staj-dev:~# for f in /proc/sys/net/ipv6/conf/*/forwarding; do echo $f;
cat $f; done
/proc/sys/net/ipv6/conf/all/forwarding
0
/proc/sys/net/ipv6/conf/default/forwarding
0
/proc/sys/net/ipv6/conf/eth0/forwarding
0
/proc/sys/net/ipv6/conf/lo/forwarding
0
/proc/sys/net/ipv6/conf/venet0/forwarding
0

Problem is that when I do:

echo "1" > /proc/sys/net/ipv6/conf/all/forwarding

HW node stops responding on IPv6 ping, reason probably is that setting
that removes default GW:

staj-dev:~# route -6
Kernel IPv6 routing table
Destination Next Hop
Flags Metric Ref Use Iface
::1/128 ::
U 0 13 1 lo
2001:718:1:e::/128 ::
U 0 0 2 lo
2001:718:1:e::23:3004/128 ::
U 0 266 1 lo
2001:718:1:e::/64 ::
U 256 217 0 eth0
fe80::/128 ::
U 0 0 2 lo
fe80::1/128 ::
U 0 0 1 lo
fe80::213:72ff:fe1b:b97/128 ::
U 0 8 1 lo
fe80::/64 ::
U 256 0 0 eth0
fe80::/64 ::
U 256 0 0 venet0
ff02::1/128 ff02::1
UC 0 229 0 eth0
ff00::/8 ::
U 256 0 0 eth0
ff00::/8 ::
U 256 0 0 venet0

When I set GW manualy it start work and it works also for VE. GREAT!

Well and now. Why setting forwarding=1 removes GW? Is there any way how
to add it there automaticaly without my attention? I'm afraid that GW IP
fe80::215:faff:fe87:3100 is somehow related to router MAC and that it
will change when router become replaced. Any sugestion on this?

Thanks a lot!
--
-----------------------
Jan Tomasek aka Semik
http://www.tomasek.cz/

Report message to a moderator

[Message index]

		IPv6 with venet By: Jan Tomasek on Mon, 09 July 2007 13:40
		Re: IPv6 with venet By: gblond on Mon, 09 July 2007 15:16
		Re: IPv6 with venet By: Jan Tomasek on Tue, 10 July 2007 07:40
		Re: IPv6 with venet By: Thorsten Schifferdeck on Tue, 10 July 2007 10:13

Previous Topic:	Failed to compile with enabled Checkpointing & restoring Virtual Environments
Next Topic:	Announce: vzdump 1.0 released

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Mon Jun 15 23:28:37 GMT 2026

Total time taken to generate the page: 0.62054 seconds