OpenVZ Forum - RDF feed
type: channel
items: Reg. Eth0
items: Re: Reg. Eth0

Reg. Eth0
type: item
description: Hi, I have PC with centos 2.6.9-42.0.2.EL. till yesterday it was working fine. yesterday I had to load Nistnet and it requires a RTC module. So I had to load this REal time Clock module from make menuconfig under device drivers, character devices, RTC. After this I did make modules_install and rebooted the PC . Now, when I start the PC, it shows Applying Intel Microcode update: FATAL: Module microcode not found Error: module microcode does not exist in /proc/modules the other error is dev eth0 has different MAC address than expected, so ignoring. At times it shows : device eth0 does not seem to be present, delaying initialization. i did /sbin/ifconfig and saw that there is no eth0 related info. only loop back interface is present. I also tried to do /sbin/ifup eth0 but it is not found. in the lspci, the driver for ethernet is REaltek 8139 and these modules are present in /lib/modules. however, if i try to do depmod and then modprobe 8139too.ko, the message is FATAL: Module 8139too not found. if i do lsmod or /proc/modules.conf, i dont see the eth0 related modules there. Please tell me what I should do? There is some sunrpc for which also the module is missing. At present I am unable to connect this pc to the rest of the network. The dmesg command gives a lot of output but there is no way I can send that to u as it is out of network now. Waiting for your reply Thanks in advance, Padmaja
creator: padmajarv
date: 2007-03-15T12:10:58-00:00

Re: Reg. Eth0
type: item
description: 1. You can always reboot to the previous kernel (until you replaced or removed it). Keep in mind for future, that keeping previous stable kernel is always a good idea. 2. I guess you probably: a) have incorrect .config file. b) or you somehow incorrectly compiled/installed the kernel. How did you build the kernel? Provide all the details about every step please. Thanks, Kirill padmaja venkata wrote: > Hi, > I have PC with centos 2.6.9-42.0.2.EL. > till yesterday it was working fine. yesterday I had to load Nistnet and > it requires a RTC module. So I had to load this REal time Clock module > from make menuconfig under device drivers, character devices, RTC. After > this I did make modules_install and rebooted the PC . Now, when I start > the PC, it shows > > Applying Intel Microcode update: FATAL: Module microcode not found > Error: module microcode does not exist in /proc/modules > the other error is dev eth0 has different MAC address than expected, so > ignoring. > > At times it shows : device eth0 does not seem to be present, delaying > initialization. > > > i did /sbin/ifconfig and saw that there is no eth0 related info. only > loop back interface is present. > I also tried to do /sbin/ifup eth0 but it is not found. in the lspci, > the driver for ethernet is REaltek 8139 and > these modules are present in /lib/modules. however, if i try to do > depmod and then modprobe 8139too.ko, the message is > FATAL: Module 8139too not found. if i do lsmod or /proc/modules.conf, i > dont see the eth0 related modules there. Please > tell me what I should do? There is some sunrpc for which also the module > is missing. At present I am unable to connect this > pc to the rest of the network. The dmesg command gives a lot of output > but there is no way I can send that to u as it is out > of network now. Waiting for your reply > > Thanks in advance, > Padmaja > > > ------------------------------------------------------------ ------------ >
creator: dev
date: 2007-03-15T16:46:06-00:00